Page Comparison

panel

Panel

borderColor	#416EB6
titleColor	#ffffff
titleBGColor	#416EB6
title	Overview

This page install guide goes over the detailed steps install a second or third generation (F2 / F3) touchscreen installation steps for an F2/F3touchscreen FasCard/FLEX reader onto an existing machine in either a high-front or top-mount position.

borderColor	#416EB6
titleColor	#FFFFFF
titleBGColor	#416EB6
title	Table of Contents

Table of Contents

Warning

title	WARNING

Disconnect any electrical device from power before performing any work on the device. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses. It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. This document assumes the installer has working knowledge of hand tools and of the target machine in question. Card Concepts Inc. takes no responsibility for the accuracy of this document or any damage that may occur to target equipment. Technical Support recommends using all appropriate safety equipment (such as hand and eye protection) during execution of the instructions below.

Note

title

C-5402/C-5426-BASE

Incompatibility

incompatibility

The below solutions are not compatible with

.

Requirements

Bw part list

Parts	C-5401,C-5520,C-6801

X080-001 Top Mount Kit

Cci kits

KitID	X080-001
ShowKitID	true
ShowKitDesc	true

X080-002 High-Front Mount Kit

Cci kits

KitID	X080-002
ShowKitID	true
ShowKitDesc	true

Orderable through your distributor:

An F2 or F3 FasCard reader

.

C-6801 Universal Mounting Kit.

For High-Front solutions:

The X080-002 High Mount Base kit.
- This kit will come with the C-6465 F2/F3 High Mount Bracket and two (2) mounting screws.

For Top Mount solutions:

The C-6452 mounting base kit.

Not Included:

Phillips bit (if using an electronic screwdriver/drill/driver) or #2 Phillips screwdriver.
T15 Secure Torx bit (if using an electronic screwdriver/drill/driver) or screwdriver with a T15 Secure Torx tip.
- Also recommend a flex extension to accommodate for any tight angles/spacing if using any type of bit driver.
Large pliers (e.g. Straight Jaw or Hex Jaw Pliers) or an adjustable wrench for tightening the C-5702 Chase Nipple & Lock Nut that comes with the C-6801 Universal Kit.
- May need two, in some cases.

Recommended if installing onto a new machine:

Drill.
1 1/8" Tungsten Carbide Tipped Hole Cutter.
Cutting Oil.
9/64" Drill Bit.
Center Punch.
Hammer.
Fine Point Permanent Marker.
Pliers.
Tape Measure.

Instructions

Warning

title

Swipe Clearance Notice

For

Required parts & tools

Readers

Bw part list

Parts	C-5401,C-5403,C-5520
ShowDesc2	true
ShowImage	true
ShowDesc1	true

Kits

Expand

title	High-Front Mount Kit

Cci kits

KitID	I-X0021
ShowKitID	true
ShowKitDesc	true

Expand

title	Top Mount Kit

Cci kits

KitID	I-X0020
ShowKitID	true
ShowKitDesc	true

Recommended tools & supplies (not included)

Expand

title	Items not included

Insert excerpt

	LCE:Master Excerpt List
	LCE:Master Excerpt List
name	FasCard reader tools and supplies
nopanel	true

Step-by-step guide

Insert excerpt

	LCE:Master Excerpt List
	LCE:Master Excerpt List
name	Warning
nopanel	true

Multiexcerpt include

macro_uuid	11bdf2e8-444e-40ae-8d37-c63eda678589
SpaceWithExcerpt	com.atlassian.confluence.content.render.xhtml.model.resource.identifiers.SpaceResourceIdentifier@7627108f
MultiExcerptName	Warning
PageWithExcerpt	_General

Step 1 - Drilling Preparation

Select

a

the part of

a

the machine where the high-front or top-mount

solution

bracket will be installed. Ensure this location, whether on the chassis or a panel, is away from any existing components or exposed wiring.
1. Mark where you may want to mount the reader with a permanent marker if needed.
Whether keeping the

section

chassis/panel intact, exposing, or removing said

section

chassis/panel, apply some cutting oil where drilling through metal will take place.

Image Removed

Drill the oiled section in question carefully using the tungsten carbide tipped hole cutter.

Image Removed

Image Added

Image Removed

Image Added

Image Removed

Image Added
With the drilled hole prepped, you are now ready to mount the reader.

Image Removed

Image Added

Step 2 - Mounting the bracket & reader

Tip
Please choose the tab that is associated with the type of installation you are completing.

High-

Front Mount

Image Removed

front mount

In a high-front mounting solution where the FasCard reader will be angled downward toward the customer in regard to taller machines, our C-6465 bracket would be used for this install.

Image Added

Expand

title	High-front mount Step-by-step guide

Attach the C-6465 High Mount Bracket in its place, securing it down with a chase nipple.

Image Removed

Image Added

Image Removed

Mount the universal bracket to the high-front bracket with two (2) 8-32 screws and feed the harness wiring through the center. Whether choosing to feed wiring first or mounting the bracket first is no problem as long as the end result (pictured below) is achieved.

Image Removed

Image AddedImage Added
Connect the harnesses to their appropriate locations in the back of the reader.
1. For information about where the individual harnesses connect to, please see F2: FasCard Touchscreen Reader.

Image Removed

1. Image Added

Mount

Slowly mount the reader to the corresponding bracket with the top lip catching the locking edge and carefully wedging the reader in place. Ensure no metal edges of the bracket are visible.

Image Removed

Image Added
Secure the reader with

available

the provided T15 secure torx screws on the bottom.
1. This may be part of the install kits or the screws used from a previous high-front solution.

Image Removed

1. Image Added
  Note
  title Screwdriver Angling
  As the reader is angled downward

in high

1. inhigh-front solutions, securing the reader may require a thinner secure torx screwdriver or a flex extension for the appropriate torx bit to accommodate for the angle.

For third generation (

Only F3

)

FasCard

EMV-ready readers, remove

readers – Remove any plastic protectors (if still present) from the touchscreen or EMV chip insert label.

Top-Mount

Image Removed

Warning

title

Swipe Clearance

Reminder

Notice

As stated above, only for

Top Mount solutions, CCI strongly recommends mounting a top mount solution 1

top-mount solutions the front of the top-mount bracket 1-1/4 inches from the front of the machine

to the edge of the reader

, to allow for card swipe clearance.

Ensure the drilled hole aligns accordingly. Mounting the top-mount bracket any further back then 1-1/

4 inches (1.25")

4inches from the front of the machine to the edge of the reader can potentially interfere with mounting the reader to the bracket and may prevent users from being able to swipe or insert a card into the reader due to lack of clearance.

In a top-mount solution, the process differs slightly from a front or high-front mounting solution. Our C-6452 bracket would be used in this

application.

orientation.

Image Added

Expand

title	Top-mount Step-by-step guide

Attach the top-mount bracket onto the top panel of the machine, securing down with the chase nipple. Ensure the appropriate wiring is fed through the center hole for connecting to the reader.

Image RemovedMount

Image Added
Connect all harnesses to the rear of the touchscreen reader where required.

Image Removed

1. For information about where the individual harnesses connect to, please see F2: FasCard Touchscreen Reader.
  Image Added
Slowly mount the reader to the corresponding bracket with the top lip catching the locking edges (