Page Comparison

PanelborderColor#416EB6titleColorwhitetitleBGColor#416EB6borderStylesolidtitle

Overview

This page is intended to walk the installer through the general steps of installing an F1 Fascard reader. For specific installation instructions, please refer to the relevant FasCard Kit Installations - Machine Configurations & Related Documents.

Multiexcerpt include

SpaceWithExcerpt	CCIDOC
MultiExcerptName	ReaderInstallAccuracy
PageWithExcerpt	_Contact Us

Required parts & tools

Reader parts

Bw part list

Parts	C-5001,C-5800,C-5700-TEMP
ShowDesc2	true
ShowImage	true
ShowDesc1	true

Tools & supplies (not included)

Expand

title	Tool/Supply List

Multiexcerpt include

MultiExcerptName	FasCard reader tools and supplies
PageWithExcerpt	LCE:Master Excerpt List

Mounting configurations

FasCard Reader

Front-Mount Example

Top-Mount Example

Inverted Front-Mount Example

Bw part list

ImageSize150

Parts	C-5001
ImageSize	150
ShowDesc2	true
ShowImage	true
ShowDesc1	true

Image Removed

Image Added

Image Removed

Image Added

Image Removed

Image Added

Step-by-step guide

Multiexcerpt include

SpaceWithExcerpt	CCIDOC
MultiExcerptName	Warning
PageWithExcerpt	_General

Expand

title	Front-Mount

Front-Mount solution

Select a suitable location on the front of the machine to mount the card reader. It's recommended that you mount the card reader as close to the coin drop as possible.
Place the C-5700-TEMP template on the face of the machine with the straight edge of template facing up. The C-5700-TEMP template has the same outside dimensions as the card reader to help align the placement of the reader.
Using a sharpie marker, mark target drill location for the reader base, using hole "D'.

Image Removed

Image Added
Using a hole saw and drill, carefully drill a 1-1/8" hole through machine front, be sure there is nothing behind target location inside the machine that can get damaged.
1. If the material is stainless steel its recommended that a pilot hole be drilled to help keep the hole saw in the desired location.

Image Removed

1. Image Added
Mount the C-5700 bracket to machine face using the C-5702 and C-5703 chase nipple and nut.
Tighten the nut with pliers, make sure the bracket remains square on the face of the machine.

Image Removed

Image Added
Feed the harnesses through the 1-1/8" hole and bracket on the machine.

Image Modified
Connect the card reader to the harnesses.
1. For information about where to connect the harnesses to, please visit F1: FasCard Wireless Reader page.

Image Removed

1. Image Added
Mount the card reader to the C-5700 bracket with the C-0141 screws.

Image Removed

Image Added
Affix the screw cover label on the card reader.

Image Removed

Image Added

Expand

title	Top-Mount

Top-Mount solution

Select a suitable +location on top of the machine to mount the card reader. It's recommended that you mount the card reader as close to the coin drop as possible.
Place C-5700-TEMP template on top of the machine lid with the straight edge of the template facing the front of the machine.
1. Align template center with center of coin drop.
2. Template should be approximately 3/4" from the front edge of machine (this is a suggestion, installer discretion).
Using a sharpie marker, mark target drill location for swipe reader base, use hole "F".

Image Removed

Image Added
Remove the machine lid (if possible).

Image Removed

Image Added
Place the lid on a solid, level surface and drill a pilot hole with the 9/64" drill bit at the previously marked drill location.

Image Removed

Image Added
Using a hole saw, drill carefully to make a 1-1/8" hole through machine lid.

Image Removed

Image Added
Mount the C-5014 reader base to lid using the C-5702 and C-5703 chase nipple and nut.
Tighten the nut with pliers make sure the base remains square on the lid.