3581 Reader Install Guide

Part #: C-6801

Desc 1: F2/F3 Reader Mounting Kit

Desc 2: Universal

   Qty: 1

1. Place the C-6700-TEMP Drill Template on the desired mounting location.

2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

3. Refer to FasCard Mounting Guide for further instructions.

Part #: C-6801

Desc 1: F2/F3 Reader Mounting Kit

Desc 2: Universal

   Qty: 1

1. Place C-5763 TWL Bracket in the intended mounting location. Using the bracket, mark the location of all four mounting holes.
   

2. Drill a hole at each marked location using a 3/16" drill bit.
   

3. Attach C-5414 Mounting Bracket to the front of C-5763 using two C-5420 screws.
   

4. Mount the C-5763 TLW Bracket using four C-5420 Screws and fasten from the inside of the panel.

Part #: C-5800

Desc 1: F1 Reader Mounting Kit

Desc 2: Universal

   Qty: 1

1. Place the C-5700-TEMP Drill Template on the desired mounting location.

2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

3. Refer to FasCard Mounting Guide for further instructions.

Part #: C-0141

Desc 1: Screw

Desc 2: 8-32 x 1-1/2" - Cap

   Qty: 2

Part #: C-1059

Desc 1: Nut

Desc 2: 10-32 - Kep

   Qty: 2

Part #: C-1070-W

Desc 1: Washer - Build: XCH

Desc 2: 1/4" x 1" O.D.

   Qty: 2

Part #: C-5027

Desc 1: Label

Desc 2: Credit Card Logo

   Qty: 1

Part #: C-5765-W

Desc 1: Mounting Bracket

Desc 2: 10 Degree - White Finish

   Qty: 1

Part #: C-5365

Desc 1: Bypass Harness

Desc 2: Alliance Coin Vault Bypass

   Qty: 1

1. Remove existing coin box and coin drop.

2. Remove connections to coin vault service switch and bridge connections using C-5365 Bypass Harness.

3. Install C-5765-W Metercase Bracket over the front of the metercase and secure using the C-1059 Kep Nut, and C-1070-W Washer.

Part #: C-0141

Desc 1: Screw

Desc 2: 8-32 x 1-1/2" - Cap

   Qty: 2

Part #: C-1059

Desc 1: Nut

Desc 2: 10-32 - Kep

   Qty: 2

Part #: C-5027

Desc 1: Label

Desc 2: Credit Card Logo

   Qty: 1

Part #: C-5760-A

Desc 1: Alliance Adapter Bracket

Desc 2: Mounts C-5760 to MeterCase

   Qty: 1

Part #: C-5762

Desc 1: Metercase Bracket - High Cap

Desc 2: Coin Slide Ready Machine

   Qty: 1

Part #: C-1070-W

Desc 1: Washer - Build: XCH

Desc 2: 1/4" x 1" O.D.

   Qty: 2

1. Remove existing coin box and coin drop.

2. Remove connections to coin vault service switch and bridge connections using C-5365 Bypass Harness.

3. Install C-5762 Metercase Bracket over the front of the metercase and secure using the C-1059 Kep Nut, and C-1070-W Washer.

Part #: C-5801

Desc 1: F1 Reader Mounting Kit

Desc 2: Front

   Qty: 1

1. Place the C-5700-TEMP Drill Template on the desired mounting location.

2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

3. Refer to FasCard Mounting Guide for further instructions.

Part #: C-6762

Desc 1: Metercase Bracket

Desc 2: Coin Slide Ready Machine

   Qty: 1

Part #: C-5414

Desc 1: F2/F3 Std. Mounting Bracket

Desc 2: Sheet metal base

   Qty: 1

Part #: C-5420

Desc 1: Screw

Desc 2: 10-32 x ¼" - Pan

   Qty: 2

Part #: C-5416

Desc 1: Screw

Desc 2: 8-32" x 3/8" - Button - Torx

   Qty: 2

Part #: C-0301

Desc 1: Topload Mounting Bolt

Desc 2:

   Qty: 1

1. Remove existing coin box and coin slide.

2. Attach C-5414 Standard Bracket to the C-6762 Metercase Bracket using (2) C-5420 10-32 x 1/4 Pan Screws.

3. Insert C-6762 Metercase Bracket into the metercase and secure using C-0301 Topload Mounting Bolt.

Part #: C-1059

Desc 1: Nut

Desc 2: 10-32 - Kep

   Qty: 2

Part #: C-1070-W

Desc 1: Washer - Build: XCH

Desc 2: 1/4" x 1" O.D.

   Qty: 2

Part #: C-5760-A

Desc 1: Alliance Adapter Bracket

Desc 2: Mounts C-5760 to MeterCase

   Qty: 1

Part #: C-6762

Desc 1: Metercase Bracket

Desc 2: Coin Slide Ready Machine

   Qty: 1

Part #: C-5365

Desc 1: Bypass Harness

Desc 2: Alliance Coin Vault Bypass

   Qty: 1

Part #: C-5420

Desc 1: Screw

Desc 2: 10-32 x ¼" - Pan

   Qty: 2

Part #: C-5416

Desc 1: Screw

Desc 2: 8-32" x 3/8" - Button - Torx

   Qty: 2

Part #: C-5414

Desc 1: F2/F3 Std. Mounting Bracket

Desc 2: Sheet metal base

   Qty: 1

1. Remove the coin drop and coin box.

2. Remove Vault Switch and bridge the wires previously connected to the Vault Switch with the C-5365 Bypass Harness.

3. Secure C-5414 F2 Mounting Bracket to the C-6903 Mounting Bracket using the (2) C-5420 10-32 x 1/4 Pan Screws.

4. Attach the C-5760-A Adapter Bracket to the C-6762 Mounting Bracket to the captured nut on the inside of the C-6762 Mounting Bracket.

5. Run all reader harnesses through the metercase and out the opening where the coin drop normally mounts.

6. Run all reader harnesses through the circular opening on the C-6762 Mounting Bracket.

7. Install the C-6762 Mounting Bracket into the front opening of the metercase so the two threaded posts of the C-5760-A Adapter Bracket line up with the openings for the coin slots. Secure in place using the (2) C-1059 Kep Nuts and (2) C-1070-W Washers.

Part #: C-1059

Desc 1: Nut

Desc 2: 10-32 - Kep

   Qty: 2

Part #: C-1070-W

Desc 1: Washer - Build: XCH

Desc 2: 1/4" x 1" O.D.

   Qty: 2

Part #: C-6765-W-R1

Desc 1: F2 Mounting Bracket

Desc 2: 10 Degree - White Finish

   Qty: 1

Part #: C-5365

Desc 1: Bypass Harness

Desc 2: Alliance Coin Vault Bypass

   Qty: 1

Part #: C-5420

Desc 1: Screw

Desc 2: 10-32 x ¼" - Pan

   Qty: 2

Part #: C-5416

Desc 1: Screw

Desc 2: 8-32" x 3/8" - Button - Torx

   Qty: 2

Part #: C-5414

Desc 1: F2/F3 Std. Mounting Bracket

Desc 2: Sheet metal base

   Qty: 1

1. Remove existing coin box and coin drop.

2. Install the C-5365 Bypass Harness by removing the coin vault switch and connecting the spade terminal connections to C-5365 Bypass Harness.

3. Attach the C-5414 F2 Mounting Bracket to the C-6765-W-R1 Metercase Bracket using (2) C-5420 10-32 x 1/4 Pan Screws.

4. Run any card reader harnesses through the coin slot openings and the circular hole in the C-6765-W-R1 Metercase Bracket.

5. Install the C-6765-W-R1 Metercase Bracket so that the two threaded posts insert into the coin drop slots. Then secure it to the machine using the (2) C-1059 Kep Nuts and (2) C-1070-W Washers.

Part #: C-0141

Desc 1: Screw

Desc 2: 8-32 x 1-1/2" - Cap

   Qty: 2

Part #: C-5027

Desc 1: Label

Desc 2: Credit Card Logo

   Qty: 1

Part #: C-5762

Desc 1: Metercase Bracket - High Cap

Desc 2: Coin Slide Ready Machine

   Qty: 1

Part #: C-0301

Desc 1: Topload Mounting Bolt

Desc 2:

   Qty: 1

1. Remove existing coin box and coin slide.

2. Install C-5762 Metercase Bracket over the front of the metercase and secure using the C-0301 Mounting Bolt.

Part #: C-5101

Desc 1: Spade Taps

Desc 2: 18-14 AWG

   Qty: 3

Part #: C-5210

Desc 1: Power Adapter Harness

Desc 2: CGI

   Qty: 1

Part #: C-5500

Desc 1: Power Extension Harness

Desc 2: 25.5"

   Qty: 1

Part #: C-5602R1

Desc 1: Power Converter

Desc 2: SMT-012-018VW

   Qty: 1

1. Use the C-5101 Spade Taps on the incoming power.

   1. Tap the L1 wire.

   2. Tap the N wire.

   3. Tap the Ground wire.

2. Take the C-5210 Power Adapter Harness and connect the red tab connectors to the following wires:

   1. Connect the blue wire to the L1 wire.

   2. Connect the brown wire to the N wire.

   3. Connect the green/yellow wire to the Ground wire.

3. Connect the 3-pin connector from the C-5210 Power Adapter Harness to the matching connection on the C-5602R1 Power Converter.

4. Connect the 4-pin connector from the C-5602R1 Power Converter to the matching connection on the C-5500 Power Extension Harness.

Part #: C-6204-40

Desc 1: Power Adapter Harness

Desc 2: F2, 12vDC Pow Harness - 40"

   Qty: 1

1. Connect the C-6204-40 12VDC Power Harness to the H10 connection on the machine control assembly.

   1. Secure the green wire beneath the ground screw.

2. Connect the opposite end of the C-6204-40 Power Adapter Harness (3-pin molex) to the F2 reader.

Part #: C-6207

Desc 1: F2/F3, Alliance ACA Power

Desc 2:

   Qty: 1

1. Connect the 2-pin connector from the C-6207 F2, ACA Power Harness to the 24v transformer behind the front control panel.

2. The remaining end (3-pin molex) connects directly to the rear of the F2 FasCard Reader.

Part #: C-5250

Desc 1: Coin Sense Harness

Desc 2:

   Qty: 1

1. Disconnect the Coin Drop from the Machine Control Assembly.

2. Connect the C-5250 Coin Sense Harness to the harness connected to the Coin Drop.

Part #: C-5253

Desc 1: Coin Sense Harness

Desc 2: 28"

   Qty: 1

1. Disconnect the Coin Drop from the Machine Control Assembly.

2. Connect the C-5253 Coin Sense Harness to the micro switch on the coin slide.

Part #: C-6250

Desc 1: Coin Sense Harness

Desc 2: F2

   Qty: 1

1. Disconnect the Coin Drop from the Machine Control Assembly.

2. Connect the C-6250 Coin Sense Harness to the harness connected to the Coin Drop.

Part #: C-6253

Desc 1: Coin Sense Harness

Desc 2: 28"

   Qty: 1

1. Disconnect the Coin Drop from the Machine Control Assembly.

2. Connect the C-6253 Coin Sense Harness to the harness connected to the Coin Slide Switch.

Part #: C-5300-NC

Desc 1: Machine Start Harness

Desc 2: Aliiance - Normally Closed

   Qty: 1

1. Connect the C-5300-NC Machine Start Harness to the harness previously connected to the coin drop.

Part #: C-5256

Desc 1: Machine Start Harns (pulse)

Desc 2: 20" - Male taps, Rq. Female

   Qty: 1

1. Connect the C-5256 Machine Start Harness to the harness previously connected to the Coin Slide Switch.

Part #: C-5240

Desc 1: Machine Start Harness

Desc 2: Alliance ACA

   Qty: 1

1. Connect the C-5240 Machine Start Harness to the H3 connection on the Machine Control Assembly.

1. Feed remaining harness ends through mounting bracket.

2. For serial setups:

   1. Connect the free end of the Machine Start Harness to port 1 (Serial Connection Port) as shown in the image above.

   2. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

3. For coin pulse setups:

   1. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

4. Connect the the Cat5 cables running to and from the adjacent machines to ports labeled 3 (Line Connection Ports) as shown in the image above.

5. Secure the LaundryCard reader to the bracketry using included hardware.

1. Feed remaining harness ends through mounting bracket.

2. For serial setups:

   1. Connect the free end of the Machine Start Harness to port 1 (Serial Connection Port) as shown in the image above.

   2. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

3. For coin pulse setups:

   1. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

4. Connect the free end of the Power Harness to port 1.

5. Secure the L2 reader to base as described in FasCard F2/F3 Reader Installation Guide - Front Mount.

1. Feed remaining harness ends through the mounting hole as described in the F1 Reader Mounting Guide.

2. Connect the free end of the Machine Start Harness to port 1 (Serial Connection Port) as shown in the image above.

3. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

4. Connect the free end of the Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.

5. Connect the free end of the Power Extension Harness to port 4 (Power Harness Connection Port) as shown in the image above.

6. Secure the FasCard reader to base as described in the F1 Reader Mounting Guide.

1. Feed remaining harness ends through the mounting hole as described in FasCard F2/F3 Reader Installation Guide - Front Mount.

2. For Serial Setups:

   1. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

   2. Connect the free end of the Machine Start Harness to port 5 (Serial Connection Port) as shown in the image above.

3. For Pulse Setups:

   1. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

4. Connect the free end of the Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.

   1. For dual coin drop setups connect the secondary Coin Sense Harness to port 4 (Coin Sense Harness Connection Port) as shown in the image above.

5. Connect the free end of the Power Harness to port 1.

6. Secure the FasCard reader to base as described in FasCard F2/F3 Reader Installation Guide - Front Mount.

TODO