3105 Reader Install Guide

Part #: C-5801

Desc 1: F1 Reader Mounting Kit

Desc 2: Front

   Qty: 1

1. Place the C-5700-TEMP Drill Template on the desired mounting location.

2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

3. Refer to FasCard Mounting Guide for further instructions.

Part #: C-0141

Desc 1: Screw

Desc 2: 8-32 x 1-1/2" - Cap

   Qty: 2

Part #: C-0303

Desc 1: Topload Mounting Bolt

Desc 2:

   Qty: 1

Part #: C-5027

Desc 1: Label

Desc 2: Credit Card Logo

   Qty: 1

Part #: C-5771

Desc 1: Metercase Bracket

Desc 2: Coin Drop Ready Machines

   Qty: 1

1. Remove coin box and coin slide.

2. Install C-5771 Metercase Bracket and secure using C-0303 Topload Mounting Bolt.

Part #: C-5801

Desc 1: F1 Reader Mounting Kit

Desc 2: Front

   Qty: 1

1. Place the C-5700-TEMP Drill Template on the desired mounting location.

2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

3. Refer to FasCard Mounting Guide for further instructions.

Part #: C-0141

Desc 1: Screw

Desc 2: 8-32 x 1-1/2" - Cap

   Qty: 2

Part #: C-0301

Desc 1: Topload Mounting Bolt

Desc 2:

   Qty: 1

Part #: C-0911

Desc 1: Metercase Bracket

Desc 2: Whirlpool - White

   Qty: 1

Part #: C-0015

Desc 1: Label

Desc 2: Reader Cover Label

   Qty: 1

1. Remove coin box and coin slide.

2. Install C-5771 Metercase Bracket into the front opening of the metercase and secure using C-0303 Topload Mounting Bolt from the inside.

3. After running the Cat5e cables and start harness through the front opening of the metercase bracket and connecting them to the LaundryCard reader, use the (2) C-0141 8-32 x 1-1/2" Socket Screws to secure the reader.

4. Apply the C-0015 Label to the front of the LaundryCard reader around the card slot.

Part #: C-0015

Desc 1: Label

Desc 2: Reader Cover Label

   Qty: 1

Part #: C-0144

Desc 1: Screw

Desc 2: 8-32 x 2" - Flat

   Qty: 2

Part #: C-0930

Desc 1: Mounting Bracket

Desc 2: Unimac/ADC

   Qty: 1

1. Use the C-0930 Mounting Bracket to mark out the center opening for the card reader and the lower set of holes to the left and right of the central opening.

   1. Ensure the positing leaves enough space for the reader's bezel to sit flat against the machine's panel and for the reader to be inserted into the machine and allow for the CAT5 cables to be connected.

2. Cut out the central opening and use a 9/64" Drill Bit to make a hole at each drill marks to the left and right of the central opening.

3. Place the C-0930 Mounting Bracket on the inside of the machine's panel. Pass through and connect the CAT5 cables and machine start harness to the reader.

4. Use the (2) C-0144 8-32 x 2" Flat Screw to attach the reader to the C-0930 Mounting Bracket.

5. Apply C-0015 Label over the area around the card slot on the front of the LaundryCard reader.

Part #: C-6801

Desc 1: F2/F3 Reader Mounting Kit

Desc 2: Universal

   Qty: 1

1. Place the C-6700-TEMP Drill Template on the desired mounting location.

2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

3. Refer to FasCard Mounting Guide for further instructions.

Part #: C-0303

Desc 1: Topload Mounting Bolt

Desc 2:

   Qty: 1

Part #: C-6911

Desc 1: F2 Metercase Bracket

Desc 2: Whirlpool - White

   Qty: 1

Part #: C-5420

Desc 1: Screw

Desc 2: 10-32 x ¼" - Pan

   Qty: 2

Part #: C-5416

Desc 1: Screw

Desc 2: 8-32" x 3/8" - Button - Torx

   Qty: 2

Part #: C-5414

Desc 1: F2/F3 Std. Mounting Bracket

Desc 2: Sheet metal base

   Qty: 1

1. Remove existing coin box and coin mechanism.

2. Run reader harnesses through the metercase and out the opening where the coin mechanism was mounted.

3. Attach the C-5414 Reader Bracket to the C-6911 Metercase Bracket using (2) C-5420 10-32 x 1/4 Pan Screws.

4. Insert the reader harnesses through the hole in the C-6911 Metercase Bracket and then insert the bracket into the metercase opening.

5. Secure the C-6911 Metercase Bracket to the metercase using the C-0301 Mounting Bolt.

Part #: C-6980

Desc 1: Maytag Bk Splash Mount

Desc 2: F2

   Qty: 1

Part #: C-1042

Desc 1: Nut

Desc 2: 8-32 - Kep

   Qty: 1

Part #: C-1070-W

Desc 1: Washer - Build: XCH

Desc 2: 1/4" x 1" O.D.

   Qty: 1

Part #: C-5416

Desc 1: Screw

Desc 2: 8-32" x 3/8" - Button - Torx

   Qty: 2

1. Remove the (4) Security T20 retaining screws from the front of the machine.
   

2. Lift up and pull panel forward and lay on machine. NOTE: The front panel may come apart, as it is two parts. Take care not to damage the ribbon cable.
   
   

3. Mount the C-6980 Mounting Bracket on the front of the panel so that the holes match on the right and the retaining screw on the back of the plate goes through the card slot.
   

4. Place the C-1070-W Washer and C-1042 Keps Nut onto the retaining screw and tighten using 11/32 socket to secure the mounting bracket. The bracket should feel slightly loose until the panel is reattached to the machine.
   

Part #: C-6362

Desc 1: Coin Sense Harness

Desc 2: MLG

   Qty: 1

1. Disconnect the Coin Drop from the Machine Control Assembly.

2. Connect the C-6362 Coin Sense Harness to the harness connected to the Coin Drop.

Part #: C-5362

Desc 1: Coin Sense Harness

Desc 2: MLG

   Qty: 1

1. Disconnect the Coin Drop from the Machine Control Assembly.

2. Connect the C-5362 Coin Sense Harness to the harness connected to the Coin Drop.

Part #: C-5364

Desc 1: Machine Start Harness

Desc 2: Maytag MFR

   Qty: 1

Locate the AA3 serial connection on the machine control board and plug in the C-5364 Machine Start Harness.

1. Feed remaining harness ends through mounting bracket.

2. For serial setups:

   1. Connect the free end of the Machine Start Harness to port 1 (Serial Connection Port) as shown in the image above.

   2. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

3. For coin pulse setups:

   1. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

4. Connect the the Cat5 cables running to and from the adjacent machines to ports labeled 3 (Line Connection Ports) as shown in the image above.

5. Secure the LaundryCard reader to the bracketry using included hardware.

1. Feed remaining harness ends through mounting bracket.

2. For serial setups:

   1. Connect the free end of the Machine Start Harness to port 1 (Serial Connection Port) as shown in the image above.

   2. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

3. For coin pulse setups:

   1. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

4. Connect the free end of the Power Harness to port 1.

5. Secure the L2 reader to base as described in FasCard F2/F3 Reader Installation Guide - Front Mount.

1. Feed remaining harness ends through the mounting hole as described in the F1 Reader Mounting Guide.

2. Connect the free end of the Machine Start Harness to port 1 (Serial Connection Port) as shown in the image above.

3. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

4. Connect the free end of the Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.

5. Connect the free end of the Power Extension Harness to port 4 (Power Harness Connection Port) as shown in the image above.

6. Secure the FasCard reader to base as described in the F1 Reader Mounting Guide.

1. Feed remaining harness ends through the mounting hole as described in FasCard F2/F3 Reader Installation Guide - Front Mount.

2. For Serial Setups:

   1. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

   2. Connect the free end of the Machine Start Harness to port 5 (Serial Connection Port) as shown in the image above.

3. For Pulse Setups:

   1. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

4. Connect the free end of the Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.

   1. For dual coin drop setups connect the secondary Coin Sense Harness to port 4 (Coin Sense Harness Connection Port) as shown in the image above.

5. Connect the free end of the Power Harness to port 1.

6. Secure the FasCard reader to base as described in FasCard F2/F3 Reader Installation Guide - Front Mount.

TODO