Skip to end of banner
Go to start of banner

3545 Reader Install Guide

Skip to end of metadata
Go to start of metadata

You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 3 Next »

Warning!

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses.

It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Overview

Equipment Details

Type: Tumble Dryer (Single)
Manufacturer: ADC
Make: ADC
Model Length: Not Set

Customer will need to confirm if the control is Phase 5 or Phase 7 to confirm which start and coin sense harnesses are required.

Associated Models


AD758
AD758V
ADG758
ADG758V

Recommended Tools and Supplies

  • Drill

  • 1 1/8" Tungsten Carbide Tipped Hole Cutter

  • Cutting Oil

  • 9/64" Drill Bit

  • Center Punch

  • Hammer

  • Fine Point Permanent Marker

  • Pliers

  • Tape Measure

Installation

Install Mounting Hardware

 I-M0104

Part #: C-5710

Desc 1: Rubber Grommet

Desc 2: 3/4"

   Qty: 1

Part #: C-6801

Desc 1: F2/F3 Reader Mounting Kit

Desc 2: Universal

   Qty: 1

  1. Place the C-6700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to FasCard Mounting Guide for further instructions.

Connect Power

 I-P0012

Part #: C-5101

Desc 1: Spade Taps

Desc 2: 18-14 AWG

   Qty: 3

Part #: C-5210

Desc 1: Power Adapter Harness

Desc 2: CGI

   Qty: 1

Part #: C-5500-60

Desc 1: Power Extension Harness

Desc 2: 60"

   Qty: 1

Part #: C-5602R1

Desc 1: Power Converter

Desc 2: SMT-012-018VW

   Qty: 1

  1. Tap power as described in the Fascard Reader Install - Universal Concepts document using the C-5101 Spade Taps provided.
  2. Connect the C-5210 Power Adapter Harness to the installed spade taps. Connect the opposite end to the C-5602 Power Converter.
  3. Connect the C-5500-60 Power Extension Harness to the appropriate connector on the C-5602 Power Converter. The remaining cable end connects to the FasCard reader.

Connect Coin Sense Harness

 I-S0038

Part #: C-6343

Desc 1: Coin Sense Harness (SA)

Desc 2: ADC Phase 5

   Qty: 1

  1. Disconnect the Coin Drop from the Machine Control Assembly.
  2. Connect the C-6343 Coin Sense Harness to the harness connected to the Coin Drop.
 I-S0049

Part #: C-6368

Desc 1: Coin Sense Harness (SA)

Desc 2: ADC Phase 7

   Qty: 1

  1. Disconnect the Coin Drop from the Machine Control Assembly.
  2. Connect the C-6368 Coin Sense Harness to the harness connected to the Coin Drop.
 I-S0050

Part #: C-6382

Desc 1: Coin Sense Harness

Desc 2: Imonex EM100/EM3

   Qty: 1

  1. Disconnect the Coin Drop from the Machine Control Assembly.
  2. Connect the C-6382 Coin Sense Harness to the 4-pin harness connected to the EM100 board.
 I-S0059

Part #: C-6343

Desc 1: Coin Sense Harness (SA)

Desc 2: ADC Phase 5

   Qty: 2

  1. Disconnect the Coin Drop from the Machine Control Assembly.
  2. Connect the first C-6343 Coin Sense Harness to the coin drop harness connected to the Coin 1 connector on the Machine Control Assembly.
  3. Connect the second C-6343 Coin Sense Harness to the coin drop harness connected to the Coin 2 connector on the Machine Control Assembly.

Connect Machine Interface Harness

 I-T0056

Part #: C-5344

Desc 1: Machine Start Harness

Desc 2: ADC Phase 5

   Qty: 1

  1. Connect the C-5344 Machine Start Harness to the Coin 1 connection on the Machine Control Assembly.
 I-T0057

Part #: C-5345

Desc 1: Machine Start Harness

Desc 2: ADC Phase 7

   Qty: 1

  1. Connect the C-5345 Machine Start Harness to the Coin 1 connection on the Machine Control Assembly.

Connect and Mount Reader

Item No.ComponentNotes
1Power Connection PortUtilizes the same power harnesses as the first generation FasCard reader.
2Pulse Connection PortConnection point for pulse machine start harnesses.
3Coin 1 Connection PortThis is the connection point for the harness input associated with Coin 1.
4Coin 2 Connection PortThis is the connection point for the harness input associated with Coin 2.
5Serial Connection PortThis is the connection point for serial machine start harnesses.
  1. Feed remaining harness ends through the mounting hole as described in the F2,F3 Reader Install Guide.
  2. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.
  3. Connect the free end of the C-6343 Coin Sense Harness connected to the Coin 1 harness to port 3 (Coin 1 Sense Harness Connection Port) as shown in the image above.
    1. Dual coin setups, connect the free end of the C-6343 Coin Sense Harness connected to the Coin 2 harness to port 4 (Coin 2 Sense Harness Connection Port) as shown in the image above.
  4. Connect the free end of the C-5500 Power Harness to port 1.
  5. Secure the FasCard reader to base as described in the FasCard Mounting Guide.

Machine Configuration

TODO

CCI Software Configuration

Machine ControlPulseSerial
Phase 5SingleVend (Relay) / 60ms*NOT SUPPORTED*
Phase 7SingleVend (Relay) / 60ms*NOT SUPPORTED*

Additional Resources

  • No labels