Skip to end of banner
Go to start of banner

3332 Reader Install Guide

Skip to end of metadata
Go to start of metadata

You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 4 Next »

Warning!

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses.

It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Overview

Equipment Details

Type: Dryer
Manufacturer: LG
Make: LG
Model Length: Not Set

Titan-C Dryer

Associated Models

TLD1840CES
TLD1840CGD
TLD1840CGS
TLD1840CGW
TLD1840QGS
TLD1840QGW

Recommended Tools and Supplies

  • Drill

  • 1 1/8" Tungsten Carbide Tipped Hole Cutter

  • Cutting Oil

  • 9/64" Drill Bit

  • Center Punch

  • Hammer

  • Fine Point Permanent Marker

  • Pliers

  • Tape Measure

Installation

Install Mounting Hardware

 I-M0003

Part #: C-6801

Desc 1: F2/F3 Reader Mounting Kit

Desc 2: Universal

   Qty: 1

  1. Place the C-6700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to Touchscreen Reader Mounting Guide (F2 & F3) for further instructions.

 I-M0166

Part #: C-6923

Desc 1: Metercase Bracket

Desc 2: LG - Grey

   Qty: 1

Part #: C-0923-ROD

Desc 1: Metercase Mounting Rod

Desc 2: LG

   Qty: 1

Part #: C-5420

Desc 1: Screw

Desc 2: 10-32 x ¼" - Pan

   Qty: 2

Part #: C-5416

Desc 1: Screw

Desc 2: 8-32" x 3/8" - Button - Torx

   Qty: 2

Part #: C-5414

Desc 1: F2/F3 Std. Mounting Bracket

Desc 2: Sheet metal base

   Qty: 1

  1. Remove existing coin box and coin drop.

  2. Attach the C-5414 F2 Mounting Bracket to the C-6923 Metercase Bracket using (2) C-5420 10-32 x 1/4 Pan Screws.

  3. Run any card reader harnesses through the coin slot openings and the circular hole in the C-6923 Metercase Bracket.

  4. Install the C-6923 Metercase Bracket into the front of the metercase and secure using the C-0923-ROD Metercase Mounting Rod from inside the metercase.

 I-M0136

Part #: C-6801

Desc 1: F2/F3 Reader Mounting Kit

Desc 2: Universal

   Qty: 1

  1. Place the C-6700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to Touchscreen Reader Mounting Guide (F2 & F3) for further instructions.

Connect Power

 I-P0003

Part #: C-5101

Desc 1: Spade Taps

Desc 2: 18-14 AWG

   Qty: 3

Part #: C-5210

Desc 1: Power Adapter Harness

Desc 2: CGI

   Qty: 1

Part #: C-5500

Desc 1: Power Extension Harness

Desc 2: 25.5"

   Qty: 1

Part #: C-5602R1

Desc 1: Power Converter

Desc 2: SMT-012-018VW

   Qty: 1

  1. Use the C-5101 Spade Taps on the incoming power.

    1. Tap the L1 wire.

    2. Tap the N/L2 wire.

    3. Tap the Ground wire.

  2. Take the C-5210 Power Adapter Harness and connect the red tab connectors to the following wires:

    1. Connect the blue wire to the L1 wire.

    2. Connect the brown wire to the N/L2 wire.

    3. Connect the green/yellow wire to the Ground wire.

  3. Connect the 3-pin connector from the C-5210 Power Adapter Harness to the matching connection on the C-5602R1 Power Converter.

  4. Connect the 4-pin connector from the C-5602R1 Power Converter to the matching connection on the C-5500 Power Extension Harness.

Connect Coin Sense Harness

 I-S0027

Part #: C-6250

Desc 1: Coin Sense Harness

Desc 2: F2

   Qty: 1

  1. Disconnect the Coin Drop from the Machine Control Assembly.

  2. Connect the C-6250 Coin Sense Harness to the harness connected to the Coin Drop.

Connect Machine Interface Harness

 I-T0046

Part #: C-5272

Desc 1: Machine Start Harness

Desc 2: LG

   Qty: 1

  1. Connect the C-5272 Machine Start Harness to the machine coin harness originally connected to the coin drop.

 I-T0087

Part #: C-5273

Desc 1: 12 Pin Start Harness

Desc 2: LG

   Qty: 1

  1. Connect the C-5273 Machine Start Harness to the 12-pin machine coin harness originally connected to the coin drop.


Connect and Mount Reader

  1. Feed remaining harness ends through the mounting hole.

  2. Connect the free end of the C-5272 or C-5273 Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

  3. (Coin and Card Installations Only) Connect the free end of the C-6250 or C-6271 Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.

  4. Connect the free end of the C-5500 Power Extension Harness to port 1 (Power Harness Connection Port) as shown in the image above.

CCI Software Configuration

Machine ControlPulseSerial
Titan-C Light - WiFi 2.0 DryerSingleVend (Relay) / 30ms*NOT SUPPORTED*

Additional Resources

  • No labels