Skip to end of banner
Go to start of banner

3670 F1 Reader Install Guide

Skip to end of metadata
Go to start of metadata

You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 10 Next »

Warning!

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses.

It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Overview

Equipment Details

Type: Front Load Washer
Manufacturer: Maytag
Make: Whirlpool
Model Length: 10

Associated Models


CHW9050AW0
CHW9060AW0

Recommended Tools and Supplies

  • Drill

  • 1 1/8" Tungsten Carbide Tipped Hole Cutter

  • Cutting Oil

  • 9/64" Drill Bit

  • Center Punch

  • Hammer

  • Fine Point Permanent Marker

  • Pliers

  • Tape Measure

Installation

Install Mounting Hardware

 I-M0006

Part #: C-5014

Desc 1: Reader Base & Gasket

Desc 2: F1

   Qty: 1

Part #: C-5027

Desc 1: Label

Desc 2: Credit Card Logo

   Qty: 1

Part #: C-5702

Desc 1: Chase Nipple

Desc 2: 3/4"

   Qty: 1

Part #: C-5703

Desc 1: Lock Nut

Desc 2: 3/4" - 102-S

   Qty: 1

Part #: C-5705

Desc 1: Screw

Desc 2: 8 x 1-1/2 Plastite

   Qty: 2

  1. Place the C-5700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to F1 Reader Mounting Guide for further instructions.

 I-M0085

Part #: C-0141

Desc 1: Screw

Desc 2: 8-32 x 1-1/2" - Cap

   Qty: 2

Part #: C-0303

Desc 1: Topload Mounting Bolt

Desc 2:

   Qty: 1

Part #: C-5027

Desc 1: Label

Desc 2: Credit Card Logo

   Qty: 1

Part #: C-5771

Desc 1: Metercase Bracket

Desc 2: Coin Drop Ready Machines

   Qty: 1

  1. Remove the mounting bolt securing the coin drop to the metercase. Then remove the coin drop and coin box.

  2. Run reader harnesses through the metercase and the hole on the C-5771 Metercase Bracket.

  3. Install C-5771 Metercase Bracket into the metercase and secure using C-0303 Mounting Bolt.
 I-M0134

Part #: C-5800

Desc 1: F1 Reader Mounting Kit

Desc 2: Universal

   Qty: 1

  1. Remove the (4) security torx retaining screws on the front of the machine.

  2. Remove the soap tray by pulling it out and pressing on the retaining tab in the rear of the tray.

  3. Locate and remove the (2) security torx screws inside the soap tray opening.
  4. Remove the final (2) torx screws to open the top cover.
  5. Locate a spot on top of the machine to mount the reader. Verify included harnesses will reach desired location without encountering interference from internal machine components. Mark the location using C-5700-TEMP Drill Template.
  6. Refer to F1 Reader Mounting Guide for instructions on drilling mounting holes and mounting the reader.

Connect Power

 I-P0007

Part #: C-5101

Desc 1: Spade Taps

Desc 2: 18-14 AWG

   Qty: 2

Part #: C-5336

Desc 1: Power Adapter Harness

Desc 2: Dexter Stack

   Qty: 1

Part #: C-5500

Desc 1: Power Extension Harness

Desc 2: 25.5"

   Qty: 1

Part #: C-5602R1

Desc 1: Power Converter

Desc 2: SMT-012-018VW

   Qty: 1

  1. Locate the incoming power cables in the rear of the machine. This should include a white, black and green wire.

  2. Use the C-5101 Spade Taps to tap the black (L1) and white (Neutral) wires.
  3. Attach the spade ends of the C-5336 Power Adapter Harness to the taps. Blue to black, and Brown to White.
  4. Attach the Green ground wire from the C-5336 Power Adapter Harness to a nearby chassis ground screw.
  5. Connect the 3-pin connector from the C-5336 Power Adapter Harness to the 3-pin connector on the C-5602R1 Power Converter.
  6. Connect the 4-pin connector from the C-5602R1 Power Converter to the 4-pin connector on the C-5500 Power Extension Harness.
  7. Mount the C-5602R1 Power Converter in the machine by using zip ties to secure it to the machine's wire harness.

Connect Coin Sense Harness

 I-S0020

Part #: C-5362

Desc 1: Coin Sense Harness

Desc 2: MLG

   Qty: 1

  1. Disconnect the Coin Drop from the Machine Control Assembly.
  2. Connect the C-5362 Coin Sense Harness to the harness connected to the Coin Drop.

Connect Machine Interface Harness

 I-T0090

Part #: C-5364

Desc 1: Machine Start Harness

Desc 2: Maytag MFR

   Qty: 1

Part #: C-0126-MLV-EXT15

Desc 1: Extension Harness

Desc 2: Compass

   Qty: 1

  1. Connect the C-5364 Machine Start Harness to the AA3 connector on the Machine Control Assembly.
    1. If needed, use the C-0126-MLV-EXT15 Extension Harness to extend the C-5364 Machine Start Harness.

Connect and Mount Reader

  1. Feed remaining harness ends through the mounting hole.
  2. Connect the free end of the C-5364 Machine Start Harness to port 1 (Serial Connection Port) as shown in the image above.
  3. Connect the free end of the C-5362 Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.
  4. Connect the free end of the C-5500 Power Extension Harness to port 4 (Power Harness Connection Port) as shown in the image above.

Machine Configuration

  1. Enter Service Mode and navigate to J option.
  2. Set option to J.d.
  3. Exit Service Mode.

CCI Software Configuration

Machine ControlPulseSerial
Gen1SingleVend (MLV+) / 24ms*NOT SUPPORTED*

Additional Resources

  • No labels