Skip to end of banner
Go to start of banner

0001 Reader Install Guide

Skip to end of metadata
Go to start of metadata

You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 6 Next »

Warning!

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses.

It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Overview

Equipment Details

Type: Tumble Dryer (Stack)
Manufacturer: ADC
Make: ADC
Model Length: 5 to 6

If machine has larger non-standard coin drop, substitute drop cover C-0963 and label C-0031.

Associated Models


AD330
AD330D
ADC330
ADG330
ADG330D
ADS330

Recommended Tools and Supplies

  • Drill

  • 1 1/8" Tungsten Carbide Tipped Hole Cutter

  • Cutting Oil

  • 9/64" Drill Bit

  • Center Punch

  • Hammer

  • Fine Point Permanent Marker

  • Pliers

  • Tape Measure

Installation

Install Mounting Hardware

 I-M0104

Part #: C-5710

Desc 1: Rubber Grommet

Desc 2: 3/4"

   Qty: 1

Part #: C-6801

Desc 1: F2/F3 Reader Mounting Kit

Desc 2: Universal

   Qty: 1

  1. Place the C-6700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to FasCard Mounting Guide for further instructions.

 I-M0124

Part #: C-0926

Desc 1: Drop Cover

Desc 2: American 330

   Qty: 1

Part #: C-1044N

Desc 1: Nut

Desc 2: M3 - Kep

   Qty: 4

Part #: C-5751

Desc 1: Screw

Desc 2: 8-32 x 2-1/2" - Flat

   Qty: 2

Part #: C-6925A

Desc 1: F2 Mounting Bracket

Desc 2: for Coin Vault - Right

   Qty: 1

Part #: C-6925B

Desc 1: F2 Mounting Bracket

Desc 2: for Coin Vault - Right

   Qty: 1

Part #: C-5420

Desc 1: Screw

Desc 2: 10-32 x ¼" - Pan

   Qty: 2

Part #: C-5416

Desc 1: Screw

Desc 2: 8-32" x 3/8" - Button - Torx

   Qty: 2

Part #: C-5414

Desc 1: F2/F3 Std. Mounting Bracket

Desc 2: Sheet metal base

   Qty: 1

  1. Remove the coin drop and coin box from the machine.

  2. Install the C-0926 Drop Cover into the coin drop opening and secure using the (4) C-1044N M3 Keps Nuts.

  3. Install the C-6925A Mounting Bracket into the coin vault. Orient so the side the threaded fasteners face outwards towards the front of the machine and are on the bottom portion of the bracket. After inserted into the coin vault, the bracket should catch the coin vault opening when facing flush with the front of the machine.

  4. Place the C-6925B Mounting Bracket Cover over the coin vault opening so the outer set of holes align with the threaded holes on the C-6925A Mounting Bracket. Then use the (2) C-5751 8-32 x 2-1/2" Screw to secure both brackets together. The C-6925A Mounting Bracket enables the C-6925B Mounting Bracket Cover to anchor over the front of the machine.

  5. Attach the C-5414 Standard F2 Mounting Bracket to the C-6925B Mounting Bracket Cover using the (2) C-5420 10-35 x 1/4" Pan Screws.

Install Mounting Hardware

 I-M0010

Part #: C-5801

Desc 1: F1 Reader Mounting Kit

Desc 2: Front

   Qty: 1

  1. Place the C-5700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to F1 Reader Mounting Guide for further instructions.

 I-M0041

Part #: C-0015

Desc 1: Label

Desc 2: Reader Cover Label

   Qty: 1

Part #: C-0032

Desc 1: Label

Desc 2: ADC Coin Drop

   Qty: 1

Part #: C-0133

Desc 1: Standoff

Desc 2: 8-32" x 1-1/2" - Hex

   Qty: 2

Part #: C-0141

Desc 1: Screw

Desc 2: 8-32 x 1-1/2" - Cap

   Qty: 2

Part #: C-0925A

Desc 1: Mounting Bracket

Desc 2: For Coin Vault Mounting

   Qty: 1

Part #: C-0925B

Desc 1: Mounting Bracket

Desc 2: For Coin Vault Mounting

   Qty: 1

Part #: C-0926

Desc 1: Drop Cover

Desc 2: American 330

   Qty: 1

Part #: C-1044N

Desc 1: Nut

Desc 2: M3 - Kep

   Qty: 4

  1. Remove existing coin box and coin drop.

  2. Insert the C-0925A Mounting Bracket into the Coin Vault. Orient the Mounting Bracket so that the threaded studs face outward.

  3. Attach the C-0133 Standoffs to the threaded studs on the Mounting Bracket.

  4. Place C-0925B Mounting Bracket Cover over the Coin Vault so that the opening for the screws line up with the Standoffs.

  5. Once the Machine Start Harness and the Ethernet Cables are ran through the rectangular opening in the brackets, secure the brackets in place by inserting the reader and attaching with C-0141 Screws.

  6. Insert C-0926 Drop Cover into the coin drop opening. Secure in place using C-1044N Kep Nuts.

  7. Apply C-0032 Coin Drop Label to the front of the Drop Cover.

 I-M0043

Part #: C-0015

Desc 1: Label

Desc 2: Reader Cover Label

   Qty: 1

Part #: C-0141

Desc 1: Screw

Desc 2: 8-32 x 1-1/2" - Cap

   Qty: 2

  1. CCI Ready Machines will already have the proper mounting and will only need to be secured to the machine using the C-0141 Screws. 

Instructions do not exist for Kit I-M0094

 I-M0104

Part #: C-5710

Desc 1: Rubber Grommet

Desc 2: 3/4"

   Qty: 1

Part #: C-6801

Desc 1: F2/F3 Reader Mounting Kit

Desc 2: Universal

   Qty: 1

  1. Place the C-6700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to FasCard F2/F3 Reader Installation Guide - Front Mount for further instructions.

 I-M0124

Part #: C-0926

Desc 1: Drop Cover

Desc 2: American 330

   Qty: 1

Part #: C-1044N

Desc 1: Nut

Desc 2: M3 - Kep

   Qty: 4

Part #: C-5751

Desc 1: Screw

Desc 2: 8-32 x 2-1/2" - Flat

   Qty: 2

Part #: C-6925A

Desc 1: F2 Mounting Bracket

Desc 2: for Coin Vault - Right

   Qty: 1

Part #: C-6925B

Desc 1: F2 Mounting Bracket

Desc 2: for Coin Vault - Right

   Qty: 1

Part #: C-5420

Desc 1: Screw

Desc 2: 10-32 x ¼" - Pan

   Qty: 2

Part #: C-5416

Desc 1: Screw

Desc 2: 8-32" x 3/8" - Button - Torx

   Qty: 2

Part #: C-5414

Desc 1: F2/F3 Std. Mounting Bracket

Desc 2: Sheet metal base

   Qty: 1

  1. Remove the coin drop and coin box from the machine.

  2. Install the C-0926 Drop Cover into the coin drop opening and secure using the (4) C-1044N M3 Keps Nuts.

  3. Install the C-6925A Mounting Bracket into the coin vault. Orient so the side the threaded fasteners face outwards towards the front of the machine and are on the bottom portion of the bracket. After inserted into the coin vault, the bracket should catch the coin vault opening when facing flush with the front of the machine.

  4. Place the C-6925B Mounting Bracket Cover over the coin vault opening so the outer set of holes align with the threaded holes on the C-6925A Mounting Bracket. Then use the (2) C-5751 8-32 x 2-1/2" Screw to secure both brackets together. The C-6925A Mounting Bracket enables the C-6925B Mounting Bracket Cover to anchor over the front of the machine.

  5. Attach the C-5414 Standard F2 Mounting Bracket to the C-6925B Mounting Bracket Cover using the (2) C-5420 10-35 x 1/4" Pan Screws.

 I-M0221

Part #: C-5710

Desc 1: Rubber Grommet

Desc 2: 3/4"

   Qty: 1

Part #: C-6802

Desc 1: FLEX RF Reader Mounting Kit

Desc 2:

   Qty: 1

  1. Place the C-6700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to FasCard F2/F3 Reader Installation Guide - Front Mount for further instructions.

Instructions do not exist for Kit I-M0240

Connect Power

 I-P0012

Part #: C-5101

Desc 1: Spade Taps

Desc 2: 18-14 AWG

   Qty: 3

Part #: C-5210

Desc 1: Power Adapter Harness

Desc 2: CGI

   Qty: 1

Part #: C-5500-60

Desc 1: Power Extension Harness

Desc 2: 60"

   Qty: 1

Part #: C-5602R1

Desc 1: Power Converter

Desc 2: SMT-012-018VW

   Qty: 1

  1. Tap the machine AC power wires using the C-5101 Spade Taps. See FasCard Reader Install - Universal Concepts for more details.

    1. For 120vac models: L1, N, and Ground wires

    2. For 240vac models: L1, L2, and Ground wires

  2. Connect the three wires from the C-5210 Power Adapter Harness to the C-5101 Spade Taps.

    1. Connect the Blue wire to the L1 tap.

    2. Connect the Brown wire to the N/L2 tap.

    3. Connect the Green/Yellow wire to the Ground tap.

  3. Connect the 3-pin connector from the C-5210 Power Adapter Harness to the matching connector on the C-5602R1 Power Converter.

  4. Connect the 4-pin connector from the C-5602R1 Power Converter to the matching connector on the C-5500-60 Power Extension Harness.

  5. Run the C-5500-60 Power Extension Harness to the reader mounting location.

Connect Coin Sense Harness

 I-S0012

Part #: C-5343

Desc 1: Coin Sense Harness (SA)

Desc 2: ADC Phase 5

   Qty: 1

  1. Disconnect the Coin Drop from the Machine Control Assembly.

  2. Connect the C-5343 Coin Sense Harness to the harness connected to the Coin Drop.

 I-S0022

Part #: C-5368

Desc 1: Coin Sense Harness

Desc 2: ADC Phase 7

   Qty: 1

  1. Disconnect the Coin Drop from the Machine Control Assembly.

  2. Connect the C-5368 Coin Sense Harness to the harness connected to the Coin Drop.

 I-S0029

Part #: C-6251

Desc 1: Coin Sense Harness (SA)

Desc 2: MD2

   Qty: 1

  1. Disconnect the Coin Drop from the Machine Control Assembly.

  2. Connect the C-6251 Coin Sense Harness to the harness connected to the Coin Drop.

 I-S0049

Part #: C-6368

Desc 1: Coin Sense Harness (SA)

Desc 2: ADC Phase 7

   Qty: 1

  1. Disconnect the Coin Drop from the Machine Control Assembly.

  2. Connect the C-6368 Coin Sense Harness to the harness connected to the Coin Drop.

Connect Machine Interface Harness

 I-T0052

Part #: C-5302

Desc 1: Machine Start Harness

Desc 2: MD2

   Qty: 1

  1. Connect the C-5302 Machine Start Harness to the Coin 1 connection on the Machine Control Assembly.

 I-T0057

Part #: C-5345

Desc 1: Machine Start Harness

Desc 2: ADC Phase 7

   Qty: 1

  1. Connect the C-5345 Machine Start Harness to the Coin 1 connection on the Machine Control Assembly.

CCI Software Configuration

Machine ControlPulseSerial
Phase 5SingleVend (Relay) / 60ms*NOT SUPPORTED*
Phase 7SingleVend (Relay) / 60ms*NOT SUPPORTED*

Additional Resources

  • No labels