Skip to end of banner
Go to start of banner

2032 Reader Install Guide

Skip to end of metadata
Go to start of metadata

You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 6 Next »

Warning!

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses.

It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Overview

Equipment Details

Type: Stack Washer/Dryer
Manufacturer: Dexter
Make: Dexter
Model Length: 22

Two kits need to be created. One for the washer unit, and one for the dryer unit. The only difference between these kits is the start harness.

Coin drop cover used in LC and Card Only kits is ordered through LaundryConcepts from Dexter.

Associated Models


SC0350ND17EC3XSWBCGUSA
SC0350NE17EC4XSWBCGUSA
SC0350NE17EC4XSWBCGUSX
SC0450NE17EC4XSWBCGUSA
SC0450NE17EC4XSWBCGUSX
SC0450NE17EC4XSWBCSUSA
SC0750NE16EC4RSWBCSUSA
SC0750NE17EC4XSWBCGUSA

Recommended Tools and Supplies

  • Drill

  • 1 1/8" Tungsten Carbide Tipped Hole Cutter

  • Cutting Oil

  • 9/64" Drill Bit

  • Center Punch

  • Hammer

  • Fine Point Permanent Marker

  • Pliers

  • Tape Measure

Installation

Install Mounting Hardware

 I-M0158

Part #: C-0144

Desc 1: Screw

Desc 2: 8-32 x 2" - Flat

   Qty: 2

Part #: C-6801

Desc 1: F2/F3 Reader Mounting Kit

Desc 2: Universal

   Qty: 1

Part #: C-6936

Desc 1: F2, Sm Vault Mount Bracket

Desc 2:

   Qty: 1

Part #: C-5035

Desc 1: Label

Desc 2: 3-7/8" x 3-1/4"

   Qty: 1

  1. Remove existing coin box.

  2. Bend the side tabs of the C-6936 Vault Bracket outward and install into the coin vault. The tabs should snap into place securing the bracket.

  3. Attach the C-5414 Mounting Bracket to the C-6936 Vault Bracket using the C-0144 Screws.

Connect Power

Connect Coin Sense Harness

 I-S0006

Part #: C-5258

Desc 1: Coin Sense Harness (SA)

Desc 2: WCAD

   Qty: 1

  1. Disconnect the Coin Drop from the Machine Control Assembly.

  2. Connect the C-5258 Coin Sense Harness to the harness connected to the Coin Drop.

 I-S0034

Part #: C-6258

Desc 1: Coin Sense Harness (SA)

Desc 2: WCAD

   Qty: 1

  1. Disconnect the Coin Drop from the Machine Control Assembly.

  2. Connect the C-6258 Coin Sense Harness to the harness connected to the Coin Drop.

Connect Machine Interface Harness

 I-T0038

Part #: C-5254

Desc 1: Machine Start Harness

Desc 2: Dexter Stack Dryer

   Qty: 1

  1. Connect the C-5254 Machine Start Harness to the Coin connection on the Machine Control Assembly.

 I-T0002

Part #: C-0127-MLV

Desc 1: Machine Start Harness

Desc 2: Dexter

   Qty: 1

  1. Connect the C-0127-MLV Machine Start Harness to the P23 connection on the Machine Control Assembly.

Connect and Mount Reader

CCI Software Configuration

Machine ControlPulseSerial
C-Series (1.5)SingleVend (Relay) / 55ms*NOT SUPPORTED*
C-Series (1.5)SingleVend (Relay) / 55msDexter C-Series Washer Extractor

Additional Resources

  • No labels