Skip to end of banner
Go to start of banner

3680 Reader Install Guide

Skip to end of metadata
Go to start of metadata

You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 3 Next »

Warning!

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses.

It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Overview

Equipment Details

Type: Tumble Dryer (Stack)
Manufacturer: Tolon
Make: Tolon
Model Length: 6

Associated Models


TRDS16
TRDS16U

Recommended Tools and Supplies

  • Drill

  • 1 1/8" Tungsten Carbide Tipped Hole Cutter

  • Cutting Oil

  • 9/64" Drill Bit

  • Center Punch

  • Hammer

  • Fine Point Permanent Marker

  • Pliers

  • Tape Measure

Installation

Install Mounting Hardware

 I-M0003

Part #: C-6801

Desc 1: F2/F3 Reader Mounting Kit

Desc 2: Universal

   Qty: 1

  1. Place the C-6700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to FasCard Mounting Guide for further instructions.

 I-M0203

Part #: C-6602-V2

Desc 1: F2, Large Vault Mount

Desc 2: Modified version

   Qty: 1

Part #: C-6601

Desc 1: Spacer

Desc 2: F2 Dexter Vault Filler Plate

   Qty: 1

Part #: C-0144

Desc 1: Screw

Desc 2: 8-32 x 2" - Flat

   Qty: 2

Part #: C-5414

Desc 1: F2/F3 Std. Mounting Bracket

Desc 2: Sheet metal base

   Qty: 1

Part #: C-5416

Desc 1: Screw

Desc 2: 8-32" x 3/8" - Button - Torx

   Qty: 2

  1. Feed all reader harness ends through the open face of the Coin Vault.
  2. Spread the C-6602 Vault Mount Bracket wings outward.
  3. Feed the harness ends through the C-6602 Vault Mount Bracket.
  4. Insert the C-6602 Vault Mount Bracket into the Coin Vault and ensure the inner tabs lock into place so it's secured in place.
  5. Feed the remaining harness ends through both the C-6601 Filler Plate and C-5414 F2 Mounting Bracket.
  6. Secure both the C-5414 F2 Mounting Bracket and C-6601 Filler Plate to the C-6602 Vault Mount Bracket with the C-0144 Screws.

Connect Power

 I-P0008

Part #: C-5101

Desc 1: Spade Taps

Desc 2: 18-14 AWG

   Qty: 3

Part #: C-5210

Desc 1: Power Adapter Harness

Desc 2: CGI

   Qty: 1

Part #: C-5500-84

Desc 1: Power Extension Harness

Desc 2: 84"

   Qty: 1

Part #: C-5602R1

Desc 1: Power Converter

Desc 2: SMT-012-018VW

   Qty: 1

  1. Tap the machine AC power wires using the C-5101 Spade Taps.
    1. For 120v models: L1, N, and Ground wires
    2. For 240v models: L1, L2, and Ground wires
  2. Connect the three wires from the C-5210 Power Adapter Harness to the C-5101 Spade Taps.
    1. Connect the Blue wire to the L1 tap.
    2. Connect the Brown wire to the N/L2 tap.
    3. Connect the Green/Yellow wire to the Ground tap.
  3. Connect the 3-pin connector from the C-5210 Power Adapter Harness to the matching connector on the C-5602R1 Power Converter.
  4. Connect the 4-pin connector from the C-5602R1 Power Converter to the matching connector on the C-5500-84 Power Extension Harness.
  5. Run the C-5500-84 Power Extension Harness to the reader mounting location.

Connect Coin Sense Harness

 I-S0046

Part #: C-6360

Desc 1: Coin Sense Harness

Desc 2: Female taps, Rq. Male

   Qty: 1

  1. Disconnect coin drop from factory machine harness.
  2. Connect C-6360 Coin Sense Harness to the coin drop.
    1. Connect red to red.
    2. Connect green to brown.
    3. Connect blue to blue.

Connect Machine Interface Harness

 I-T0040

Part #: C-5256

Desc 1: Machine Start Harns (pulse)

Desc 2: 20" - Male taps, Rq. Female

   Qty: 1

  1. Connect the C-5256 Machine Start Harness to the harness originally connected to the coin drop.
    1. Connect to the black and brown wires.
    2. To prevent any potential electrical issues, apply electrical tape over the blue wire connector.

Connect and Mount Reader

  1. Feed remaining harness ends through the mounting hole.
  2. Connect the free end of the C-5256 Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.
  3. (Coin and Card Installation Only) Connect the free end of the C-6360 Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.
  4. Connect the free end of the C-5500-84 Power Extension Harness to port 1 (Power Harness Connection Port) as shown in the image above.

CCI Software Configuration

Machine ControlPulseSerial
*NO NAME*SingleVend (Relay) / 100ms*NOT SUPPORTED*

Additional Resources

  • No labels