Skip to end of banner
Go to start of banner

3285 Reader Install Guide

Skip to end of metadata
Go to start of metadata

You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 6 Next »

Warning!

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses.

It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Overview

Equipment Details

Type: Washer Extractor
Manufacturer: Continental
Make: Continental
Model Length: 14 to 17

Serial start harness requires the machine to be equipped with a serial daughterboard. This is not a standard feature and will need to have the installer confirm if this board is present.

When setting up, customer will have to relay what extra option the machine is setup for. Select the appropriate equipment type when setting up equipment on FasCard/LaundryCard.

"Continental ProfitPlus Washer" is only a placehold/legacy equipment. New equipment should be using v59 or newer machine firmware and will require selecting on of the following:
• "Continental ProfitPlus Washer - Delicate"
• "Continental ProfitPlus Washer - Extra Spin"
• "Continental ProfitPlus Washer - Sanitize"

Associated Models


EH020C1111111111
EH020CA1311026
EH020CA131112
EH020CA1311121
EH020CA1311210
EH020CA132112100
EH020CA132412100
EH020CA13241210000
EH020X030040
EH020X1111111111
EH020X1132111101
EH020X1132112101
EH020X1182112101
EH020X123112101
EH020X2132111101
EH020X2182111101
EH020XA131121011
EH020XA132110101
EH020XA132111101
EH020XA13211201
EH020XA132112011
EH020XA1321121.
EH020XA132112100
EH020XA1321121001
EH020XA132112101
EH020XA1321121011
EH020XA13211210111
EH020XA132112107
EH020XA1324
EH020XA1324121011
EH020XA1324121012022
EH020XA182112101
EH020XA1821121011
EH020XA192112101
EH020XA1921121011
EH020XA312112101
EH030C1
EH030C1111111111
EH030C1131111
EH030C11311111
EH030C113111111
EH030C11321110
EH030C11321111
EH030C113211110
EH030X113211101
EH030X1132111100
EH030X1132111101
EH030X11321111011
EH030X11321111101
EH030X1132112101
EH030X1182111011
EH030X1182111101
EH030XA182112101
EH040C11321110
EH040C1132111100
EH040CA1321121
EH040X113211011
EH040X113211100
EH040X1132111011
EH040X1132111100
EH040X1132111101
EH040X11321111011
EH040X1132111102
EH040X11321111101
EH040X1182111101
EH040X11821111011
EH040X11821111011111
EH040X11921111011
EH040X21321111011
EH040XA131121011
EH040XA1321121
EH055C11321110
EH055C113211110
EH055C213211110
EH055X1132111100
EH055X1132111101
EH055X2132111101
EH060CA1321121
EH060X113211101
EH060X1132111011
EH060X1132111100
EH060X1132111101
EH060X11321111011
EH060X113211110111
EH060X1132111110
EH060X11321111101
EH060X1182111101
EH060X11821111011
EH060X2132111101
EH060X21321111011
EH060X21321111101
EH060X2182111101
EH060X221321111011
EH060X3182111101
EH060XA131121011
EH080CA1321121
EH080X1132111101
EH080X213111101
EH080X2132111011
EH080X2132111101
EH080X21321111011
EH080X21321111101
EH080X2182111101
EH080XA1321121
EH090C1132111100
EH090C2132111000
EH090C213211160
EH090CA1321121
EH090X1132111101
EH090X21021110101
EH090X2123211101
EH090X21311111011
EH090X2132111011
EH090X2132111101
EH090X21321111011
EH090X2182111101
EH090X21921111011
EH090X3182111101
EH130X2102110101
EH130X2102111010
EH130X21021110101
EH130X21321111011
EH130X2181111011
EH130X21811111011
EH130X21821110101
EH130X2182111011
EH130X2182111101
EH130X21821111011
EH130X2182111111
EH130X282111011
EH130XA182112101
EM020CA13211210
EM025CA1321121
EM040C1132111100
EM055C11321111
EM055C1132111100

Recommended Tools and Supplies

  • Drill

  • 1 1/8" Tungsten Carbide Tipped Hole Cutter

  • Cutting Oil

  • 9/64" Drill Bit

  • Center Punch

  • Hammer

  • Fine Point Permanent Marker

  • Pliers

  • Tape Measure

Installation

Install Mounting Hardware

Connect Power

Connect Coin Sense Harness

 I-S0054

Part #: C-6332

Desc 1: Coin Sense Harness (SA)

Desc 2: CGI EM

   Qty: 1

  1. Disconnect the Coin Drop from the Machine Control Assembly.

  2. Connect the C-6332 Coin Sense Harness to the harness connected to the Coin Drop.

    1. Connect the Red connector to the Coin Acceptor connection, where the coin drop was previously connected, on the Machine Control Assembly.

 I-C0012

Part #: C-6330

Desc 1: Combination Harness

Desc 2: CGI EM

   Qty: 1

  1. Disconnect the Coin Drop from the Machine Control Assembly.

  2. Connect the white, male, 8-pin connector from the C-6330 Combination Harness to the harness connected to the Coin Drop.

Connect Machine Interface Harness

 I-T0017

Part #: C-0114-MLV

Desc 1: Machine Start Harness

Desc 2: Continental

   Qty: 1

  1. Connect the C-0114-MLV Machine Start Harness to the middle X1 port on the serial communication board.

  2. The RJ11 connector on the end of the C-0114-MLV Machine Start Harness will fit into the middle X1 RJ45 port even though the RJ11 connector is smaller in size.

 I-C0012

Part #: C-6330

Desc 1: Combination Harness

Desc 2: CGI EM

   Qty: 1

  1. Connect the red, female, 8-pin connector of the C-6330 Combination Harness to the Coin Acceptor connector on the Machine Control Assembly.

Connect and Mount Reader

 LaundryCard Reader (C-0100, C-0101, C-0102, C-0103)

  1. Feed remaining harness ends through mounting bracket.

  2. For serial setups:

    1. Connect the free end of the Machine Start Harness to port 1 (Serial Connection Port) as shown in the image above.

    2. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

  3. For coin pulse setups:

    1. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

  4. Connect the the Cat5 cables running to and from the adjacent machines to ports labeled 3 (Line Connection Ports) as shown in the image above.

  5. Secure the LaundryCard reader to the bracketry using included hardware.

 LaundryCard L2 Reader (C-0103-L2)

L2_Port_Guide.png

  1. Feed remaining harness ends through mounting bracket.

  2. For serial setups:

    1. Connect the free end of the Machine Start Harness to port 1 (Serial Connection Port) as shown in the image above.

    2. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

  3. For coin pulse setups:

    1. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

  4. Connect the free end of the Power Harness to port 1.

  5. Secure the L2 reader to base as described in FasCard F2/F3 Reader Installation Guide - Front Mount.

 F1 Reader (C-5001)

  1. Feed remaining harness ends through the mounting hole as described in the F1 Reader Mounting Guide.

  2. Connect the free end of the Machine Start Harness to port 1 (Serial Connection Port) as shown in the image above.

  3. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

  4. Connect the free end of the Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.

  5. Connect the free end of the Power Extension Harness to port 4 (Power Harness Connection Port) as shown in the image above.

  6. Secure the FasCard reader to base as described in the F1 Reader Mounting Guide.

 F2/FLEX Reader (C-5401, C-5402, C-5402E)

  1. Feed remaining harness ends through the mounting hole as described in FasCard F2/F3 Reader Installation Guide - Front Mount.

  2. For Serial Setups:

    1. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

    2. Connect the free end of the Machine Start Harness to port 5 (Serial Connection Port) as shown in the image above.

  3. For Pulse Setups:

    1. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

  4. Connect the free end of the Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.

    1. For dual coin drop setups connect the secondary Coin Sense Harness to port 4 (Coin Sense Harness Connection Port) as shown in the image above.

  5. Connect the free end of the Power Harness to port 1.

  6. Secure the FasCard reader to base as described in FasCard F2/F3 Reader Installation Guide - Front Mount.

 F3 Reader (C-5520, C-5520E)

TODO

Machine Configuration

ProfitPlus Controls

  1. Connect the washer and open the door. The display will show door.

  2. Press and hold down key 1 until the Cod report appears on the display.

  3. Enter the access code into the menus by pressing the sequence of eight keys of the code without interruption. In basic configuration (when the machine is delivered) the access code to ADVANCED MODE is: 12341234.

  4. If the sequence entered is correct, the display will show Pro, corresponding to the first menu ADVANCED MODE.

  5. Keys 2 and 4 allow the selection of the precedent table menus. The menu selected is shown on the display following its keyword. To enter in it, press key 1 when displaying it.

  6. Navigate to Mod > ID and set value to '1'.

  7. Exit ADVANCE MODE.

CCI Software Configuration

Machine ControlPulseSerial
Coin ControlSingleVend (Relay) / 500msContinental Coin Control Washer
ProfitPlusSingleVend (Relay) / 500msContinental ProfitPlus Washer

Additional Resources

  • No labels