Skip to end of banner
Go to start of banner

3279 Reader Install Guide

Skip to end of metadata
Go to start of metadata

You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 4 Next »

Warning!

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses.

It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Overview

Equipment Details

Type: Washer Extractor
Manufacturer: Dexter
Make: Dexter
Model Length: Not Set

For card only installations, customer has to clarify if machine is a coin or card prepped model to select the correct mounting kit.

If coin and card installation, customer must clarify what type of coin drop is installed in the machine. Mechanical or Optical.

Associated Models

WCVD18KCS10
WCVD18KCS10USA0
WCVD18KCS12
WCVD18KCS12EC1X
WCVD18KCS12SSBS
WCVD18KCS12USA
WCVD18KCS12USX
WCVD20KCS12
WCVD20KCS12USSZ
WCVD25KCS10
WCVD25KCS12
WCVD25KCS12USA
WCVD30KCS12
WCVD30KCS12USSZ
WCVD40KCS10
WCVD40KCS12
WCVD40KCS12000
WCVD40KCS120000
WCVD40KCS12EC1X
WCVD40KCS12USA
WCVD50KCS12
WCVD55KCS000000
WCVD55KCS10
WCVD55KCS12
WCVD55KCS120000
WCVD55KCS12EC1X
WCVD55KCS12SSBS
WCVD55KCS12USA
WCVD55KCS12USSZ
WCVD55KCS12USX
WCVD55KCS12USXX
WCVD75KCS12
WCVD75KCS12EC1X
WCVD75KCS12USA
WCVD75KCS12USA0

Recommended Tools and Supplies

  • Drill

  • 1 1/8" Tungsten Carbide Tipped Hole Cutter

  • Cutting Oil

  • 9/64" Drill Bit

  • Center Punch

  • Hammer

  • Fine Point Permanent Marker

  • Pliers

  • Tape Measure

Installation

Install Mounting Hardware

 I-M0003

Part #: C-6801

Desc 1: F2/F3 Reader Mounting Kit

Desc 2: Universal

   Qty: 1

  1. Place the C-6700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to FasCard Mounting Guide for further instructions.

 I-M0167

Part #: C-6801

Desc 1: F2/F3 Reader Mounting Kit

Desc 2: Universal

   Qty: 1

Part #: C-5035

Desc 1: Label

Desc 2: 3-7/8" x 3-1/4"

   Qty: 1

Part #: C-5710

Desc 1: Rubber Grommet

Desc 2: 3/4"

   Qty: 1

  1. Place the C-6700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Place C-5035 Label over card slot opening.

  4. Refer to FasCard Mounting Guide for further instructions.

Connect Power

 I-P0001

Part #: C-5602R1

Desc 1: Power Converter

Desc 2: SMT-012-018VW

   Qty: 1

Part #: C-5500

Desc 1: Power Extension Harness

Desc 2: 25.5"

   Qty: 1

Part #: C-5338

Desc 1: Power Adapter Harness

Desc 2: WCAD

   Qty: 1

  1. Tap power as described in the Fascard Reader Install - Universal Concepts document by connecting the C-5338 Power Adapter Harness to the power distribution panel inside the machine or tapping as needed.

    1. 120vac- Connect Brown and Blue wires to connector #2 closest to outside of machine and #4 on terminal side closest to circuit board.

    2. 240vac- Connect Brown and Blue wires to connectors 3 and 5 on the terminal side closest to the circuit board.

    3. Secure the green wire beneath the ground screw.

  2. Connect the opposite end of the C-5338 Power Adapter Harness to the C-5602 Power Converter.

  3. Connect the C-5500 Power Extension Harness to the appropriate connector on the C-5602 Power Converter. The remaining cable end connects to the FasCard reader.

Connect Coin Sense Harness

 I-S0031

Part #: C-6253

Desc 1: Coin Sense Harness

Desc 2: 28"

   Qty: 1

  1. Disconnect the Coin Drop from the Machine Control Assembly.

  2. Connect the C-6253 Coin Sense Harness to the harness connected to the Coin Drop.

Connect Machine Interface Harness

 I-T0038

Part #: C-5254

Desc 1: Machine Start Harness

Desc 2: Dexter Stack Dryer

   Qty: 1

  1. Connect the C-5254 Machine Start Harness to the P2 connector on the Machine Control Assembly.

Connect and Mount Reader

Item No.

Component

Notes

1

Power Connection Port

Utilizes the same power harnesses as the first generation FasCard reader.

2

Pulse Connection Port

Connection point for pulse machine start harnesses.

3

Coin 1 Connection Port

This is the connection point for the harness input associated with Coin 1.

4

Coin 2 Connection Port

This is the connection point for the harness input associated with Coin 2.

5

Serial Connection Port

This is the connection point for serial machine start harnesses.

  1. Feed remaining harness ends through the mounting hole as described in the F2/F3: FasCard Reader Mounting Guide.

  2. Connect the free end of the C-5254 Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

  3. Connect the free end of the C-6253 Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.

  4. Connect the free end of the C-5500 Power Harness to port 1.

  5. Secure the FasCard reader to base as described in the FasCard Mounting Guide.

Machine Configuration

TODO

CCI Software Configuration

Machine ControlPulseSerial
*NO NAME*SingleVend (Relay) / 55ms*NOT SUPPORTED*

Additional Resources

  • No labels