Skip to end of banner
Go to start of banner

3659 Reader Install Guide

Skip to end of metadata
Go to start of metadata

You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 4 Next »

Warning!

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses.

It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Overview

Equipment Details

Type: Top Load Washer
Manufacturer: Wascomat
Make: Encore
Model Length: 9 to 11

Coin models and card models both use the metercase and can use the same card only installation kit.

Associated Models


WMTW4371C2FMI
WMTW4371M
WMTW4371MC2
WMTW4371MCWDC

Recommended Tools and Supplies

  • Drill

  • 1 1/8" Tungsten Carbide Tipped Hole Cutter

  • Cutting Oil

  • 9/64" Drill Bit

  • Center Punch

  • Hammer

  • Fine Point Permanent Marker

  • Pliers

  • Tape Measure

Installation

Install Mounting Hardware

 I-M0003

Part #: C-6801

Desc 1: F2/F3 Reader Mounting Kit

Desc 2: Universal

   Qty: 1

  1. Place the C-6700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to FasCard Mounting Guide for further instructions.

 I-M0194

Part #: C-6912

Desc 1: F2 Metercase Bracket

Desc 2: Encore - Grey

   Qty: 1

Part #: C-1059

Desc 1: Nut

Desc 2: 10-32 - Kep

   Qty: 2

Part #: C-5420

Desc 1: Screw

Desc 2: 10-32 x ¼" - Pan

   Qty: 2

Part #: C-5416

Desc 1: Screw

Desc 2: 8-32" x 3/8" - Button - Torx

   Qty: 2

Part #: C-5414

Desc 1: F2/F3 Std. Mounting Bracket

Desc 2: Sheet metal base

   Qty: 1

  1. Remove existing coin drop and coin box from the metercase.

  2. Attach the C-5414 F2 Mounting Bracket to the C-6912 Metercase Bracket using (2) C-5420 10-32 x 1/4 Pan Screws.

  3. Run the C-5500 Power Extension Harness and C-5355 Machine Start Harness through the metercase and then through the circular opening in the C-6912 Metercase Bracket.

  4. Insert the assembled C-6912 Metercase Bracket into the metercase and secure from the inside using the C-1059 Keps Nuts.

Connect Power

 I-P0003

Part #: C-5101

Desc 1: Spade Taps

Desc 2: 18-14 AWG

   Qty: 3

Part #: C-5210

Desc 1: Power Adapter Harness

Desc 2: CGI

   Qty: 1

Part #: C-5500

Desc 1: Power Extension Harness

Desc 2: 25.5"

   Qty: 1

Part #: C-5602R1

Desc 1: Power Converter

Desc 2: SMT-012-018VW

   Qty: 1

  1. Use the C-5101 Spade Taps on the incoming power.

    1. Tap the black L1 wire.

    2. Tap the white N wire.

    3. Tap the green G wire.

  2. Take the C-5210 Power Adapter Harness and connect the red tab connectors to the following wires:

    1. Connect the blue wire to the black L1 wire.

    2. Connect the brown wire to the white N wire.

    3. Connect the green/yellow wire to the green G wire.

  3. Connect the 3-pin connector from the C-5210 Power Adapter Harness to the matching connection on the C-5602R1 Power Converter.

  4. Connect the 4-pin connector from the C-5602R1 Power Converter to the matching connection on the C-5500 Power Extension Harness.

Connect Coin Sense Harness

Connect Machine Interface Harness

 I-T0062

Part #: C-5355

Desc 1: Machine Start Harness

Desc 2: Crossover

   Qty: 1

  1. Connect the C-5355 Machine Start Harness to the CN4 Payment Device Connection located inside the metercase.

Connect and Mount Reader

Machine Configuration

Encore FLW Controls

  1. Press the Service Switch to enter Service Mode. The display will go blank.

  2. Press the Heavy Soil and Extra Rinse buttons simultaneously. The display will show either "0 00" if in coin mode and "1 00" if in card mode.

  3. If in coin mode, press the Start button. The display will begin flashing.

  4. Press the Cold button to change the left-most digit from "0" to "1".

  5. Press the Start button. The display will stop flashing.

  6. Press the Service Switch to exit Service Mode.

CCI Software Configuration

Machine ControlPulseSerial
EncoreSingleVend (MLV+) / 75msLaundrylux Crossover Encore

Additional Resources

  • No labels