Skip to end of banner
Go to start of banner

3449 Reader Install Guide

Skip to end of metadata
Go to start of metadata

You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 6 Current »

Warning!

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses.

It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Overview

Equipment Details

Type: Vending
Manufacturer: Vend-Rite
Make: Vend-Rite
Model Length: Not Set

Machines shipped after Fall 2011 have the newer style white bracket that accepts either a reader or coin mech.

Machines shipped in 2019 or later are not compatible with the C-0972 or C-6972 mounting brackets.

Associated Models

DVM360
VM120BN
VM120C
VM120D
VM120M
VM240
VM240BN
VM240C
VM240D
VM240M
VM360
VM360C
VM360D
VM360DS
VM360M

Recommended Tools and Supplies

  • Drill

  • 1 1/8" Tungsten Carbide Tipped Hole Cutter

  • Cutting Oil

  • 9/64" Drill Bit

  • Center Punch

  • Hammer

  • Fine Point Permanent Marker

  • Pliers

  • Tape Measure

Installation

Install Mounting Hardware

 I-M0036

Part #: C-0015

Desc 1: Label

Desc 2: Reader Cover Label

   Qty: 1

Part #: C-0141

Desc 1: Screw

Desc 2: 8-32 x 1-1/2" - Cap

   Qty: 4

Part #: C-0801

Desc 1: Mounting Bracket

Desc 2: Door - painted black

   Qty: 1

Part #: C-1042

Desc 1: Nut

Desc 2: 8-32 - Kep

   Qty: 2

Part #: C-1070-W

Desc 1: Washer - Build: XCH

Desc 2: 1/4" x 1" O.D.

   Qty: 2

  1. Locate an appropriate location to cut a hole for the reader where the start harness can still reach the MDB connection on the control board, or with a MDB harness.

  2. Cut a hole into the machine's panel using the C-0801 Mounting Bracket as a template. Marking out the location for the large central opening and the two unthreaded holes to the top and bottom of the opening.

  3. Place C-0801 Mounting Bracket on the panel and secure reader to the panel using the (2) C-0141 8-32 x 1-1/2" screws, (2) C-1070-W 1/4" x 1" Washers and (2) C-1042 8-32 Keps Nuts.

  4. Attach the reader using (2) C-0141 8-32 x 1-1/2" screws and apply the C-0015 Label over the screw openings.

 I-M0038

Part #: C-0015

Desc 1: Label

Desc 2: Reader Cover Label

   Qty: 1

Part #: C-0141

Desc 1: Screw

Desc 2: 8-32 x 1-1/2" - Cap

   Qty: 2

Part #: C-0972

Desc 1: Mounting Bracket

Desc 2: Bill Validator Insert

   Qty: 1

  1. Remove existing Coin Drop or Bill Validator.

  2. Install C-0972 Mounting Bracket where the Coin Drop or Bill Validator was previously installed. Use the existing hardware to secure the bracket.

 I-M0082

Part #: C-0972

Desc 1: Mounting Bracket

Desc 2: Bill Validator Insert

   Qty: 1

Part #: C-5027

Desc 1: Label

Desc 2: Credit Card Logo

   Qty: 1

Part #: C-5751

Desc 1: Screw

Desc 2: 8-32 x 2-1/2" - Flat

   Qty: 2

  1. Remove existing payment device, or cover plate.

  2. Using existing hardware, secure C-0972 Bill Validator Plate into payment device bay.

  3. After connecting harnesses to the reader, secure the reader to C-0972 Bill Validator Plate using C-5751 Screws.

  4. Optional: Apply C-5027 Label for any accepted credit cards.

 I-M0117

Part #: C-6972

Desc 1: Vend-Rite 240/360 Mount

Desc 2: Powder coated steel

   Qty: 1

Part #: C-5420

Desc 1: Screw

Desc 2: 10-32 x ¼" - Pan

   Qty: 2

Part #: C-5416

Desc 1: Screw

Desc 2: 8-32" x 3/8" - Button - Torx

   Qty: 2

Part #: C-5414

Desc 1: F2/F3 Std. Mounting Bracket

Desc 2: Sheet metal base

   Qty: 1

  1. Remove existing payment device or payment device bay cover.

  2. Install C-6972 Vend-Rite Mounting Bracket in the payment device bay. Secure in place using factory hardware.

  3. Attach C-5414 Mounting Bracket to the C-6972 Vend-Rite Mounting Bracket using the (2) C-5420 10-32 x 1/4 Pan Screws.

 I-M0174

Part #: C-6801

Desc 1: F2/F3 Reader Mounting Kit

Desc 2: Universal

   Qty: 1

  1. Place the C-6700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to FasCard F2/F3 Reader Installation Guide - Front Mount for further instructions.

 I-M0188

Part #: C-5801

Desc 1: F1 Reader Mounting Kit

Desc 2: Front

   Qty: 1

  1. Place the C-5700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to F1 Reader Mounting Guide for further instructions.

Instructions do not exist for Kit I-M0234

Instructions do not exist for Kit I-M0270

 I-M0117

Part #: C-6972

Desc 1: Vend-Rite 240/360 Mount

Desc 2: Powder coated steel

   Qty: 1

Part #: C-5420

Desc 1: Screw

Desc 2: 10-32 x ¼" - Pan

   Qty: 2

Part #: C-5416

Desc 1: Screw

Desc 2: 8-32" x 3/8" - Button - Torx

   Qty: 2

Part #: C-5414

Desc 1: F2/F3 Std. Mounting Bracket

Desc 2: Sheet metal base

   Qty: 1

  1. Follow the Vend-Rite supplied installation instructions to mount the C-5433 Mounting Bracket to the machine using the factory supplied hardware.

Connect Machine Interface Harness

 I-T0071

Part #: C-0124-MLV

Desc 1: Machine Start Harness

Desc 2: MDB Communication

   Qty: 1

  1. Connect the C-0124-MLV Machine Start Harness to the MDB connector on the Machine Control Assembly.

  2. FasCard Only: Use the pigtail connection to reconnect existing devices.

 I-C0020

Part #: C-6124-MDB

Desc 1: Machine Start Harness

Desc 2: F2 MDB Interface Harness

   Qty: 1

  1. Connect the male, 6-pin connector from the C-6124-MDB Machine Start Harness to the MDB connection on the Machine Control Assembly.

  2. Optional (FasCard Only): Use the female, 6-pin pigtail connector from the C-6124-MDB to reconnect any existing payment devices.

Connect and Mount Reader

 LaundryCard Reader (C-0100, C-0101, C-0102, C-0103)

  1. Feed remaining harness ends through mounting bracket.

  2. For serial setups:

    1. Connect the free end of the Machine Start Harness to port 1 (Serial Connection Port) as shown in the image above.

    2. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

  3. For coin pulse setups:

    1. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

  4. Connect the the Cat5 cables running to and from the adjacent machines to ports labeled 3 (Line Connection Ports) as shown in the image above.

  5. Secure the LaundryCard reader to the bracketry using included hardware.

 LaundryCard L2 Reader (C-0103-L2)

L2_Port_Guide.png

  1. Feed remaining harness ends through mounting bracket.

  2. For serial setups:

    1. Connect the free end of the Machine Start Harness to port 1 (Serial Connection Port) as shown in the image above.

    2. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

  3. For coin pulse setups:

    1. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

  4. Connect the free end of the Power Harness to port 1.

  5. Secure the L2 reader to base as described in FasCard F2/F3 Reader Installation Guide - Front Mount.

 F1 Reader (C-5001)

  1. Feed remaining harness ends through the mounting hole as described in the F1 Reader Mounting Guide.

  2. Connect the free end of the Machine Start Harness to port 1 (Serial Connection Port) as shown in the image above.

  3. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

  4. Connect the free end of the Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.

  5. Connect the free end of the Power Extension Harness to port 4 (Power Harness Connection Port) as shown in the image above.

  6. Secure the FasCard reader to base as described in the F1 Reader Mounting Guide.

 F2/FLEX Reader (C-5401, C-5402, C-5402E)

  1. Feed remaining harness ends through the mounting hole as described in FasCard F2/F3 Reader Installation Guide - Front Mount.

  2. For Serial Setups:

    1. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

    2. Connect the free end of the Machine Start Harness to port 5 (Serial Connection Port) as shown in the image above.

  3. For Pulse Setups:

    1. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

  4. Connect the free end of the Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.

    1. For dual coin drop setups connect the secondary Coin Sense Harness to port 4 (Coin Sense Harness Connection Port) as shown in the image above.

  5. Connect the free end of the Power Harness to port 1.

  6. Secure the FasCard reader to base as described in FasCard F2/F3 Reader Installation Guide - Front Mount.

 F3 Reader (C-5520, C-5520E)

TODO

  1. Feed remaining harness ends through the mounting hole as described in the FasCard F2/F3 Reader Installation Guide - Front Mount.

  2. Connect the black, 10-pin connection of the C-6124-MDB Machine Start Harness to port 5 (Serial Connection Port) as shown in the image above.

  3. Connect the clear, 3-pin connection of the C-6124-MDB Power Harness to port 1.

  4. Secure the FasCard reader to base as described in the FasCard F2/F3 Reader Installation Guide - Front Mount.

CCI Software Configuration

Machine ControlPulseSerial
MDB*NOT SUPPORTED*Vending - MDB Level 1

Additional Resources

  • No labels