Skip to end of banner
Go to start of banner

0001 Reader Install Guide

Skip to end of metadata
Go to start of metadata

You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 4 Next »

Install Mounting Hardware

 I-M0104

Part #: C-5710

Desc 1: Rubber Grommet

Desc 2: 3/4"

   Qty: 1

Part #: C-6801

Desc 1: F2/F3 Reader Mounting Kit

Desc 2: Universal

   Qty: 1

  1. Place the C-6700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to FasCard Mounting Guide for further instructions.

 I-M0124

Part #: C-0926

Desc 1: Drop Cover

Desc 2: American 330

   Qty: 1

Part #: C-1044N

Desc 1: Nut

Desc 2: M3 - Kep

   Qty: 4

Part #: C-5751

Desc 1: Screw

Desc 2: 8-32 x 2-1/2" - Flat

   Qty: 2

Part #: C-6925A

Desc 1: F2 Mounting Bracket

Desc 2: for Coin Vault - Right

   Qty: 1

Part #: C-6925B

Desc 1: F2 Mounting Bracket

Desc 2: for Coin Vault - Right

   Qty: 1

Part #: C-5420

Desc 1: Screw

Desc 2: 10-32 x ¼" - Pan

   Qty: 2

Part #: C-5416

Desc 1: Screw

Desc 2: 8-32" x 3/8" - Button - Torx

   Qty: 2

Part #: C-5414

Desc 1: F2/F3 Std. Mounting Bracket

Desc 2: Sheet metal base

   Qty: 1

  1. Remove the coin drop and coin box from the machine.
  2. Install the C-0926 Drop Cover into the coin drop opening and secure using the (4) C-1044N M3 Keps Nuts.
  3. Install the C-6925A Mounting Bracket into the coin vault. Orient so the side the threaded fasteners face outwards towards the front of the machine and are on the bottom portion of the bracket. After inserted into the coin vault, the bracket should catch the coin vault opening when facing flush with the front of the machine.
  4. Place the C-6925B Mounting Bracket Cover over the coin vault opening so the outer set of holes align with the threaded holes on the C-6925A Mounting Bracket. Then use the (2) C-5751 8-32 x 2-1/2" Screw to secure both brackets together. The C-6925A Mounting Bracket enables the C-6925B Mounting Bracket Cover to anchor over the front of the machine.
  5. Attach the C-5414 Standard F2 Mounting Bracket to the C-6925B Mounting Bracket Cover using the (2) C-5420 10-35 x 1/4" Pan Screws.

Connect Power

 I-P0012

Part #: C-5101

Desc 1: Spade Taps

Desc 2: 18-14 AWG

   Qty: 3

Part #: C-5210

Desc 1: Power Adapter Harness

Desc 2: CGI

   Qty: 1

Part #: C-5500-60

Desc 1: Power Extension Harness

Desc 2: 60"

   Qty: 1

Part #: C-5602R1

Desc 1: Power Converter

Desc 2: SMT-012-018VW

   Qty: 1

  1. Tap power as described in the Fascard Reader Install - Universal Concepts document using the C-5101 Spade Taps provided.
  2. Connect the C-5210 Power Adapter Harness to the installed spade taps. Connect the opposite end to the C-5602 Power Converter.
  3. Connect the C-5500 Power Extension Harness to the appropriate connector on the C-5602 Power Converter. The remaining cable end connects to the FasCard reader.

Connect Coin Sense Harness

 I-S0029

Part #: C-6251

Desc 1: Coin Sense Harness (SA)

Desc 2: MD2

   Qty: 1

  1. Disconnect the Coin Drop from the Machine Control Assembly.
  2. Connect the C-6251 Coin Sense Harness to the harness connected to the Coin Drop.
 I-S0049

Part #: C-6368

Desc 1: Coin Sense Harness (SA)

Desc 2: ADC Phase 7

   Qty: 1

  1. Disconnect the Coin Drop from the Machine Control Assembly.
  2. Connect the C-6368 Coin Sense Harness to the harness connected to the Coin Drop.

Connect Machine Interface Harness

 I-T0052

Part #: C-5302

Desc 1: Machine Start Harness

Desc 2: MD2

   Qty: 1

  1. Connect the C-5302 Machine Start Harness to the Coin 1 connection on the Machine Control Assembly.
 I-T0057

Part #: C-5345

Desc 1: Machine Start Harness

Desc 2: ADC Phase 7

   Qty: 1

  1. Connect the C-5345 Machine Start Harness to the Coin 1 connection on the Machine Control Assembly.

  • No labels