3105 LaundryCard Reader Install Guide

Owned by David Bussman
Last updated: Jan 23, 2024 by Chris Kite
2 min read

Warning!

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses.

It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Overview

Equipment Details

Type: Washer
Manufacturer: Maytag
Make: Maytag
Model Length: 8 to 10

Associated Models


MAT20PDA00
MAT20PDAWW
MAT20PDAWW1
MAT20PRAWW
MAT20PRAWW1
MAT20PRAYW
MAT23PRAWW

Recommended Tools and Supplies

  • Drill

  • 1 1/8" Tungsten Carbide Tipped Hole Cutter

  • Cutting Oil

  • 9/64" Drill Bit

  • Center Punch

  • Hammer

  • Fine Point Permanent Marker

  • Pliers

  • Tape Measure

Installation

Install Mounting Hardware

 I-M0009

Part #: C-0141

Desc 1: Screw

Desc 2: 8-32 x 1-1/2" - Cap

   Qty: 2

Part #: C-0301

Desc 1: Topload Mounting Bolt

Desc 2:

   Qty: 1

Part #: C-0911

Desc 1: Metercase Bracket

Desc 2: Whirlpool - White

   Qty: 1

Part #: C-0015

Desc 1: Label

Desc 2: Reader Cover Label

   Qty: 1

  1. Remove coin box and coin slide.

  2. Install C-5771 Metercase Bracket into the front opening of the metercase and secure using C-0303 Topload Mounting Bolt from the inside.

  3. After running the Cat5e cables and start harness through the front opening of the metercase bracket and connecting them to the LaundryCard reader, use the (2) C-0141 8-32 x 1-1/2" Socket Screws to secure the reader.

  4. Apply the C-0015 Label to the front of the LaundryCard reader around the card slot.

 I-M0044

Part #: C-0015

Desc 1: Label

Desc 2: Reader Cover Label

   Qty: 1

Part #: C-0144

Desc 1: Screw

Desc 2: 8-32 x 2" - Flat

   Qty: 2

Part #: C-0930

Desc 1: Mounting Bracket

Desc 2: Unimac/ADC

   Qty: 1

  1. Use the C-0930 Mounting Bracket to mark out the center opening for the card reader and the lower set of holes to the left and right of the central opening.

    1. Ensure the positing leaves enough space for the reader's bezel to sit flat against the machine's panel and for the reader to be inserted into the machine and allow for the CAT5 cables to be connected.

  2. Cut out the central opening and use a 9/64" Drill Bit to make a hole at each drill marks to the left and right of the central opening.

  3. Place the C-0930 Mounting Bracket on the inside of the machine's panel. Pass through and connect the CAT5 cables and machine start harness to the reader.

  4. Use the (2) C-0144 8-32 x 2" Flat Screw to attach the reader to the C-0930 Mounting Bracket.

  5. Apply C-0015 Label over the area around the card slot on the front of the LaundryCard reader.

Connect Machine Interface Harness

 I-T0004

Part #: C-5364

Desc 1: Machine Start Harness

Desc 2: Maytag MFR

   Qty: 1

  1. Connect the C-5364 Machine Start Harness to the Debit/AA3 connector on the Machine Control Assembly.

Connect and Mount Reader

  1. Feed remaining harness ends through the mounting hole.

  2. Connect the free end of the C-5364 Machine Start Harness to port 1 (Serial Connection Port) as shown in the image above.

  3. Connect the the Cat5 cables running to and from the adjacent machines to ports labeled 3 (Line Connection Ports) as shown in the image above.

  4. Secure the LaundryCard reader to the bracket using included hardware.

Machine Configuration

CCI Software Configuration

Machine ControlPulseSerial
Gen2SingleVend (MLV+) / 24msMaytag Gen2 M17 Top-Load Washer

Additional Resources