0470 LaundryCard Reader Install Guide

Owned by Brett Norrell (Deactivated)
Last updated: Jan 24, 2024 by Chris Kite
1 min read

Warning!

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses.

It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Overview

Equipment Details

Type: Washer Extractor
Manufacturer: Laundrylux
Make: Electrolux
Model Length: Not Set

N = Normal Spin (100G)
S = Super Spin (200G)

Associated Models


W5105N
W5105S
W5130N
W5130S
W5180N
W5180S
W5250N
W5250S
W5300S
W5330N
W5330S
W5350S
W5380S

Recommended Tools and Supplies

  • Drill

  • 1 1/8" Tungsten Carbide Tipped Hole Cutter

  • Cutting Oil

  • 9/64" Drill Bit

  • Center Punch

  • Hammer

  • Fine Point Permanent Marker

  • Pliers

  • Tape Measure

Installation

Install Mounting Hardware

 I-M0033

Part #: C-0015

Desc 1: Label

Desc 2: Reader Cover Label

   Qty: 1

Part #: C-0141

Desc 1: Screw

Desc 2: 8-32 x 1-1/2" - Cap

   Qty: 2

Part #: C-0928

Desc 1: Mounting Bracket

Desc 2: 7" Angled

   Qty: 1

Part #: C-1059

Desc 1: Nut

Desc 2: 10-32 - Kep

   Qty: 2

  1. Remove existing coin box and coin drop.

  2. Install the C-0928 Mounting Bracket over the coin vault and coin drop opening. Secure to the machine using the C-1059 kep nuts.

 I-M0032

Part #: C-0015

Desc 1: Label

Desc 2: Reader Cover Label

   Qty: 1

Part #: C-0141

Desc 1: Screw

Desc 2: 8-32 x 1-1/2" - Cap

   Qty: 2

Part #: C-0934

Desc 1: Mounting Bracket

Desc 2: 7" Straight

   Qty: 1

Part #: C-1059

Desc 1: Nut

Desc 2: 10-32 - Kep

   Qty: 2

  1. Remove existing coin box and coin drop.

  2. Install the C-0934 Mounting Bracket over the coin vault and coin drop opening. Secure to the machine using the C-1059 kep nuts.

Connect Machine Interface Harness

 I-T0031

Part #: C-0126R1

Desc 1: Machine Start Harness (SA)

Desc 2: 20" - LaundryLux

   Qty: 1

  1. Connect the C-0126R1 Machine Start Harness to the Coin 1 connector on the Machine Control Assembly.

 I-T0073

Part #: C-0126-MLV

Desc 1: Machine Start Harness (SA)

Desc 2: Wascomat Compass

   Qty: 1

Part #: C-5359

Desc 1: Machine Start Harness (SA)

Desc 2: Compass

   Qty: 1

  1. Connect the C-0126-MLV Machine Start Harness to the RS-232 port on the Machine Control Assembly.

  2. Connect the C-5359 Machine Start Harness to the Input 1 port on the Machine Control Assembly.

Connect and Mount Reader

  1. Feed remaining harness ends through mounting bracket.

  2. For serial setups:

    1. Connect the free end of the C-5359 Machine Start Harness to port 1 (Serial Connection Port) as shown in the image above.

    2. Connect the free end of the C-0126-MLV Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

  3. For coin pulse setups:

    1. Connect the free end of the C-0126R1 Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

  4. Connect the the Cat5 cables running to and from the adjacent machines to ports labeled 3 (Line Connection Ports) as shown in the image above.

  5. Secure the LaundryCard reader to the bracket using included hardware.

Machine Configuration

TODO

CCI Software Configuration

Machine ControlPulseSerial
Compass Pro (Gen7)SingleVend (Relay) / ?Laundrylux Compass Pro Washer

Additional Resources