3663 LaundryCard Reader Install Guide

Owned by David Bussman
Last updated: Jan 24, 2024 by Chris Kite
1 min read

Warning!

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses.

It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Overview

Equipment Details

Type: Small Dryer (Single)
Manufacturer: Wascomat
Make: Encore
Model Length: 11 to 10

Associated Models


DLHF0315EC2DC
DLHF0315EC2FMI
DLHF0315EDC
DLHF0315EM
DLHF0315EOPL
DLHF0315GC2DC
DLHF0315GC2FMI
DLHF0315GDC
DLHF0817E
DLHF0817EDC
DLHF0817G
DLHF0817GM
DLHS0315EC2FMI
DLHS0315GC2FMI

Recommended Tools and Supplies

  • Drill

  • 1 1/8" Tungsten Carbide Tipped Hole Cutter

  • Cutting Oil

  • 9/64" Drill Bit

  • Center Punch

  • Hammer

  • Fine Point Permanent Marker

  • Pliers

  • Tape Measure

Installation

Install Mounting Hardware

 I-M0207

Part #: C-0133

Desc 1: Standoff

Desc 2: 8-32" x 1-1/2" - Hex

   Qty: 2

Part #: C-0141

Desc 1: Screw

Desc 2: 8-32 x 1-1/2" - Cap

   Qty: 2

Part #: C-0015

Desc 1: Label

Desc 2: Reader Cover Label

   Qty: 1

Part #: C-0906

Desc 1: Spacer Plate

Desc 2: 5 1/2" x 4 3/8"

   Qty: 1

Part #: C-0936

Desc 1: Vault Mount Bracket

Desc 2:

   Qty: 1

Part #: C-5035

Desc 1: Label

Desc 2: 3-7/8" x 3-1/4"

   Qty: 1

  1. Remove existing coin box and coin drop.

  2. Bend the side tabs of the C-0936 Vault Bracket outward and install into the coin vault. The tabs should snap into place securing the bracket.

  3. Attach the (2) C-0133 8-32 x 1-1/2" Hex Standoffs to the C-0936 Vault Bracket.

  4. Run the ethernet cables and start harness through the coin vault opening and C-0936 Vault Bracket.

  5. Before attaching the reader to the C-0936 Vault Bracket remove the protective film from the C-0906 Spacer Plate and place between the reader and the machine's front panel so it aligns with the C-0936 Vault Bracket openings.

  6. Attach the reader to the (2) C-0133 8-32 x 1-1/2" Hex Standoffs using the (2) C-0141 8-32 x 1-1/2" Socket Screws.

  7. Once installation is complete and the reader has been setup and tested, apply the C-0015 label over the front of the reader.

  8. Apply the C-5035 Label over the coin drop opening.

Connect Machine Interface Harness

 I-T0062

Part #: C-5355

Desc 1: Machine Start Harness

Desc 2: Crossover

   Qty: 1

  1. Connect the C-5355 Machine Start Harness to the CN4 Payment-Device Connection.

  2. Run the C-5355 Machine Start Harness to the reader mounting location.

Connect and Mount Reader

  1. Feed remaining harness ends through the mounting hole.

  2. Connect the free end of the C-5355 Machine Start Harness to port 1 (Serial Connection Port) as shown in the image above.

  3. Connect the the Cat5 cables running to and from the adjacent machines to ports labeled 3 (Line Connection Ports) as shown in the image above.

  4. Secure the LaundryCard reader to the bracket using included hardware.

CCI Software Configuration

Machine ControlPulseSerial
EncoreSingleVend (MLV+) / 75ms*NOT SUPPORTED*

Additional Resources