0006 LaundryCard Reader Install Guide

Owned by Chris Kite
Last updated: Jan 24, 2024
1 min read

Warning!

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses.

It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Overview

Equipment Details

Type: Tumble Dryer (Stack)
Manufacturer: ADC
Make: ADC
Model Length: 6 to 8

Requires two install kits. One for the left and right sides.

Associated Models


ADG530
ADG530HB
ADG530HS

Recommended Tools and Supplies

  • Drill

  • 1 1/8" Tungsten Carbide Tipped Hole Cutter

  • Cutting Oil

  • 9/64" Drill Bit

  • Center Punch

  • Hammer

  • Fine Point Permanent Marker

  • Pliers

  • Tape Measure

Installation

Install Mounting Hardware

 I-M0040

Part #: C-0015

Desc 1: Label

Desc 2: Reader Cover Label

   Qty: 1

Part #: C-0032

Desc 1: Label

Desc 2: ADC Coin Drop

   Qty: 1

Part #: C-0133

Desc 1: Standoff

Desc 2: 8-32" x 1-1/2" - Hex

   Qty: 2

Part #: C-0141

Desc 1: Screw

Desc 2: 8-32 x 1-1/2" - Cap

   Qty: 2

Part #: C-0924A

Desc 1: Mounting Bracket

Desc 2: ADC 360 - Left

   Qty: 1

Part #: C-0924B

Desc 1: Mounting Bracket

Desc 2: ADC 360 - Left

   Qty: 1

Part #: C-0926

Desc 1: Drop Cover

Desc 2: American 330

   Qty: 1

Part #: C-1044N

Desc 1: Nut

Desc 2: M3 - Kep

   Qty: 2

  1. Remove the existing coin drop.

    1. Refer to manufacturer documentation as needed.

  2. Install C-0926 Drop Cover over the cavity left by removing the coin drop. Secure in place using the C-1044N Kep Nut.

  3. Apply C-0032 Coin Drop Label over the C-0926 Drop Cover.

  4. Install the C-0924A Mounting Bracket into the coin vault and attach C-0133 Standoffs.

  5. When installing reader, place C-0924B Cover Bracket over the coin vault before inserting the card reader. Then secure in place the brackets and reader using the C-0141 Screws.

 I-M0041

Part #: C-0015

Desc 1: Label

Desc 2: Reader Cover Label

   Qty: 1

Part #: C-0032

Desc 1: Label

Desc 2: ADC Coin Drop

   Qty: 1

Part #: C-0133

Desc 1: Standoff

Desc 2: 8-32" x 1-1/2" - Hex

   Qty: 2

Part #: C-0141

Desc 1: Screw

Desc 2: 8-32 x 1-1/2" - Cap

   Qty: 2

Part #: C-0925A

Desc 1: Mounting Bracket

Desc 2: For Coin Vault Mounting

   Qty: 1

Part #: C-0925B

Desc 1: Mounting Bracket

Desc 2: For Coin Vault Mounting

   Qty: 1

Part #: C-0926

Desc 1: Drop Cover

Desc 2: American 330

   Qty: 1

Part #: C-1044N

Desc 1: Nut

Desc 2: M3 - Kep

   Qty: 4

  1. Remove the existing coin drop.

    1. Refer to manufacturer documentation as needed.

  2. Install C-0926 Drop Cover over the cavity left by removing the coin drop. Secure in place using the C-1044N Kep Nut.

  3. Apply C-0032 Coin Drop Label over the C-0926 Drop Cover.

  4. Install the C-0925A Mounting Bracket into the coin vault and attach C-0133 Standoffs.

  5. When installing reader, place C-0925B Cover Bracket over the coin vault before inserting the card reader. Then secure in place the brackets and reader using the C-0141 Screws.

Connect Machine Interface Harness

 I-T0024

Part #: C-0118

Desc 1: Machine Start Harness

Desc 2: ADC Phase 5

   Qty: 1

  1. Connect the C-0118 Machine Start Harness to the Coin connection on the Machine Control Assembly.

Connect and Mount Reader

  1. Feed remaining harness ends through mounting bracket.

  2. Connect the free end of the C-0118 Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

  3. Connect the the Cat5 cables running to and from the adjacent machines to ports labeled 3 (Line Connection Ports) as shown in the image above.

  4. Secure the LaundryCard reader to the bracket using included hardware.

Machine Configuration

Set machine to start on a single pulse.

CCI Software Configuration

Machine ControlPulseSerial
Phase 5SingleVend (Relay) / 60ms*NOT SUPPORTED*

Additional Resources