3667 F1 Reader Install Guide

Owned by David Bussman
Last updated: Jan 23, 2024 by Chris Kite
2 min read

Warning!

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses.

It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Overview

Equipment Details

Type: Washer Extractor
Manufacturer: Laundrylux
Make: Electrolux
Model Length: 8

Equipment control and start harnesses will not be displayed unless full model number is entered. Must end in "CV" for Clarus Vibe equipped models and "CC" for Compass Pro equipped models.

Associated Models


EED6085
EED620
EED620CC
EED620CV
EED630
EED630CC
EED630CCG:2
EED630CV
EED645
EED645CC
EED645CCG:2
EED645CV
EED665
EED665CC
EED665CV
EED685
EED685CC
EED685CV
ELD620
ELD620CC
ELD620CV
ELD625
ELD630
ELD630CC
ELD630CV
ELD645
ELD645CC
ELD665
ELD665CC
ELD665CV
ELD680
ELD685
ELD685CC
ESD6135
ESD6135CC
EUD6018CC
EUD6018PPNGA0
EUD6018PPNGA0CC
EUD6018PPNGA0CV
EUD6018VFNGA0
EUD6018VPNGA0
EUD6030PPNGA0
EUD6045PPNGA0
EUD6045VFNGAF
EUD6045VPNGAF
EUD6060PPNGA0
EUD6060VPNGAF
EUD6080PPNGA0
EUD6080VFNGAF
EUD6080VPNGAF
EUD618
EUD618CC
EUD618CV
EUD620
EUD620CC
EUD625CV
EUD630
EUD630CC
EUD630CV
EUD645
EUD645CC
EUD645CV
EUD660
EUD660CC
EUD660CV
EUD660CZ
EUD665
EUD680
EUD680CC
EUD680CV

Recommended Tools and Supplies

  • Drill

  • 1 1/8" Tungsten Carbide Tipped Hole Cutter

  • Cutting Oil

  • 9/64" Drill Bit

  • Center Punch

  • Hammer

  • Fine Point Permanent Marker

  • Pliers

  • Tape Measure

Installation

Install Mounting Hardware

 I-M0142

Part #: C-5800

Desc 1: F1 Reader Mounting Kit

Desc 2: Universal

   Qty: 1

  1. Place the C-5700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to FasCard Mounting Guide for further instructions.

Connect Power

 I-P0003

Part #: C-5101

Desc 1: Spade Taps

Desc 2: 18-14 AWG

   Qty: 3

Part #: C-5210

Desc 1: Power Adapter Harness

Desc 2: CGI

   Qty: 1

Part #: C-5500

Desc 1: Power Extension Harness

Desc 2: 25.5"

   Qty: 1

Part #: C-5602R1

Desc 1: Power Converter

Desc 2: SMT-012-018VW

   Qty: 1

  1. Use the C-5101 Spade Taps on the incoming power.

    1. Tap the L1 wire.

    2. Tap the N / L2 wire.

    3. Tap the Ground wire.

  2. Take the C-5210 Power Adapter Harness and connect the red tab connectors to the following wires:

    1. Connect the blue wire to the L1 wire.

    2. Connect the brown wire to the N / L2 wire.

    3. Connect the green/yellow wire to the Ground wire.

  3. Connect the 3-pin connector from the C-5210 Power Adapter Harness to the matching connection on the C-5602R1 Power Converter.

  4. Connect the 4-pin connector from the C-5602R1 Power Converter to the matching connection on the C-5500 Power Extension Harness.

Connect Coin Sense Harness

 I-S0016

Part #: C-5357

Desc 1: Coin Sense Harness (SA)

Desc 2: Card Edge Connector

   Qty: 1

  1. Disconnect the Coin Drop from the metercase coin board.

  2. Connect the C-5357 Coin Sense Harness to the harness connected to the Coin Drop.

Connect Machine Interface Harness

 I-T0073

Part #: C-0126-MLV

Desc 1: Machine Start Harness (SA)

Desc 2: Wascomat Compass

   Qty: 1

Part #: C-5359

Desc 1: Machine Start Harness (SA)

Desc 2: Compass

   Qty: 1

  1. Connect the C-0126-MLV Machine Start Harness to the RS-232 port on the Machine Control Assembly.

  2. Connect the C-5359 Machine Start Harness to the Input 1 port on the Machine Control Assembly.

Connect and Mount Reader

  1. Feed remaining harness ends through the mounting hole.

  2. Connect the free end of the C-5359 Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

  3. Connect the free end of the C-0126-MLV Machine Start Harness to port 1 (Serial Connection Port) as shown in the image above.

  4. (Coin and Card Installation Only) Connect the free end of the C-5357 Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.

  5. Connect the free end of the C-5500 Power Extension Harness to port 4 (Power Harness Connection Port) as shown in the image above.

CCI Software Configuration

Machine ControlPulseSerial
Clarus VibeSingleVend (Relay) / 500msLaundrylux Clarus Vibe
Compass Pro (Gen7)SingleVend (Relay) / 500msLaundrylux Compass Pro Washer

Additional Resources