0133 F1 Reader Install Guide

Owned by Brett Norrell (Deactivated)
Last updated: Jan 23, 2024 by Chris Kite
2 min read

Warning!

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses.

It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Overview

Equipment Details

Type: Washer Extractor
Manufacturer: Laundrylux
Make: Electrolux
Model Length: 5

N = Normal Spin (100G)
S = Super Spin (200G)

Associated Models


W585N
W585S
W585SC

Recommended Tools and Supplies

  • Drill

  • 1 1/8" Tungsten Carbide Tipped Hole Cutter

  • Cutting Oil

  • 9/64" Drill Bit

  • Center Punch

  • Hammer

  • Fine Point Permanent Marker

  • Pliers

  • Tape Measure

Installation

Install Mounting Hardware

 I-M0142

Part #: C-5800

Desc 1: F1 Reader Mounting Kit

Desc 2: Universal

   Qty: 1

  1. Place the C-5700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to FasCard Mounting Guide for further instructions.

 I-M0086

Part #: C-0141

Desc 1: Screw

Desc 2: 8-32 x 1-1/2" - Cap

   Qty: 2

Part #: C-0928

Desc 1: Mounting Bracket

Desc 2: 7" Angled

   Qty: 1

Part #: C-1059

Desc 1: Nut

Desc 2: 10-32 - Kep

   Qty: 2

Part #: C-5027

Desc 1: Label

Desc 2: Credit Card Logo

   Qty: 1

  1. Remove existing coin box and coin drop.

  2. Insert the C-0928 Mounting Bracket into the coin vault. Secure in place using the C-1059 Kep Nuts.

  3. Apply the C-5027 Label to the FasCard Reader.

Connect Power

 I-P0003

Part #: C-5101

Desc 1: Spade Taps

Desc 2: 18-14 AWG

   Qty: 3

Part #: C-5210

Desc 1: Power Adapter Harness

Desc 2: CGI

   Qty: 1

Part #: C-5500

Desc 1: Power Extension Harness

Desc 2: 25.5"

   Qty: 1

Part #: C-5602R1

Desc 1: Power Converter

Desc 2: SMT-012-018VW

   Qty: 1

  1. Tap power as described in the Fascard Reader Install - Universal Concepts document using the C-5101 Spade Taps provided.

  2. Connect the C-5210 Power Adapter Harness to the installed spade taps. Connect the opposite end to the C-5602 Power Converter.

  3. Connect the C-5500 Power Extension Harness to the appropriate connector on the C-5602 Power Converter. The remaining cable end connects to the FasCard reader.

Connect Coin Sense Harness

 I-S0016

Part #: C-5357

Desc 1: Coin Sense Harness (SA)

Desc 2: Card Edge Connector

   Qty: 1

  1. Disconnect the Coin Drop from the Machine Control Assembly.

  2. Connect the C-5357 Coin Sense Harness to the harness connected to the Coin Drop.

Connect Machine Interface Harness

 I-T0059

Part #: C-5353R1

Desc 1: Machine Start Harness (SA)

Desc 2: 40" - LaundryLux

   Qty: 1

  1. Connect the C-5353R1 Machine Start Harness to the Coin 1 port on the Machine Control Assembly.

 I-T0073

Part #: C-0126-MLV

Desc 1: Machine Start Harness (SA)

Desc 2: Wascomat Compass

   Qty: 1

Part #: C-5359

Desc 1: Machine Start Harness (SA)

Desc 2: Compass

   Qty: 1

  1. Connect the C-0126-MLV Machine Start Harness to the RS-232 port on the Machine Control Assembly.

  2. Connect the C-5359 Machine Start Harness to the Input 1 port on the Machine Control Assembly.

Connect and Mount Reader

  1. Feed remaining harness ends through the mounting hole as described in the F1: FasCard Reader Mounting Guide.

  2. Connect the free end of the C-0126-MLV Machine Start Harness to port 1 (Serial Connection Port) as shown in the image above.

  3. Connect the free end of the C-5359 Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

  4. Connect the free end of the C-5357 Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.

  5. Connect the free end of the C-5500 Power Extension Harness to port 4 (Power Harness Connection Port) as shown in the image above.

  6. Secure the FasCard reader to base as described in the FasCard Mounting Guide.