3581 F1 Reader Install Guide

Warning!

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses.

It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Overview

Equipment Details

Type: Small Dryer (Single)
Manufacturer: Alliance
Make: [VARIES]
Model Length: 15

Associated Models

HDCBYRGS113CW01
HDEBCAGS173TW01
HDEBCRGS173TW01
HDEBCRGS175TW01
HDEBCRGS176TW01
HDEBYAGS173CW01
HDEBYAGS173TW01
HDEBYRGS116TW01
HDEBYRGS173TW01
HDESXRGS173TW01
HDGBCAGF116TW01
HDGBCAGS113TW01
HDGBCAGS116TW01
HDGBCASG116TW01
HDGBCRGF113TW01
HDGBCRGS113TW01
HDGBCRGS116EW01
HDGBCRGS116GW01
HDGBCRGS116TW01
HDGBYAGS113CW01
HDGBYAGS113TW01
HDGBYASP116TW01
HDGBYRGS1130T01
HDGBYRGS113TW01
HDGBYRGS116TW01
HDGSXRGS113TW01
HDSBYRGS116TW01
KDEBXRGS176TW01
KDESXAGS173YW01
KDESXRGS173TW01
KDGBXRGS115TW01
KDGBXRGS116TW01
KDNBXRGS173PW01
SDENCAGS1732W01
SDENCAGS173TW01
SDENCAGS176TW01
SDENCRGS173TW01
SDENCRGS173TW02
SDENCRGS176TW01
SDENXRGS173TW01
SDENYAGF173TW01
SDENYAGS103TW01
SDENYAGS116TW01
SDENYAGS153TW01
SDENYAGS1732W01
SDENYAGS173TW01
SDENYAGS176FW01
SDENYAGS176TW01
SDENYRGS173TW01
SDENYRGS176TW01
SDESXRGS173TW01
SDGNCAGS113TW01
SDGNCAGS116TW01
SDGNCAGS173PW01
SDGNCRGS113TW01
SDGNCRGS113TW02
SDGNCRGS116TW01
SDGNXRGS113TW02
SDGNXRGS116TW01
SDGNYAGS113TW01
SDGNYAGS116TW01
SDGNYRGF116TW01
SDGNYRGS113TW01
SDGNYRGS116TW01
SDGSXR2G113TW01
SDGSXRGF113EW01
SDGSXRGS113TW01
SDGSXRGS113TW02
SDGSXRSP115TW02

Recommended Tools and Supplies

Drill
1 1/8" Tungsten Carbide Tipped Hole Cutter
Cutting Oil
9/64" Drill Bit
Center Punch
Hammer
Fine Point Permanent Marker
Pliers
Tape Measure

Installation

Install Mounting Hardware

I-M0142

Part #: C-5800

Desc 1: F1 Reader Mounting Kit

Desc 2: Universal

Qty: 1

Place the C-5700-TEMP Drill Template on the desired mounting location.
Verify included harnesses will reach desired location without encountering interference from internal machine components.
Refer to FasCard Mounting Guide for further instructions.

I-M0205

Part #: C-0141

Desc 1: Screw

Desc 2: 8-32 x 1-1/2" - Cap

Qty: 2

Part #: C-5027

Desc 1: Label

Desc 2: Credit Card Logo

Qty: 1

Part #: C-5762

Desc 1: Metercase Bracket - High Cap

Desc 2: Coin Slide Ready Machine

Qty: 1

Part #: C-0301

Desc 1: Topload Mounting Bolt

Desc 2:

Qty: 1

Remove existing coin box and coin slide.
Install C-5762 Metercase Bracket over the front of the metercase and secure using the C-0301 Mounting Bolt.

I-M0079

Part #: C-0141

Desc 1: Screw

Desc 2: 8-32 x 1-1/2" - Cap

Qty: 2

Part #: C-1059

Desc 1: Nut

Desc 2: 10-32 - Kep

Qty: 2

Part #: C-5027

Desc 1: Label

Desc 2: Credit Card Logo

Qty: 1

Part #: C-5760-A

Desc 1: Alliance Adapter Bracket

Desc 2: Mounts C-5760 to MeterCase

Qty: 1

Part #: C-5762

Desc 1: Metercase Bracket - High Cap

Desc 2: Coin Slide Ready Machine

Qty: 1

Part #: C-1070-W

Desc 1: Washer - Build: XCH

Desc 2: 1/4" x 1" O.D.

Qty: 2

Remove existing coin box and coin drop.
Remove connections to coin vault service switch and bridge connections using C-5365 Bypass Harness.
Install C-5762 Metercase Bracket over the front of the metercase and secure using the C-1059 Kep Nut, and C-1070-W Washer.

I-M0078

Part #: C-0141

Desc 1: Screw

Desc 2: 8-32 x 1-1/2" - Cap

Qty: 2

Part #: C-1059

Desc 1: Nut

Desc 2: 10-32 - Kep

Qty: 2

Part #: C-1070-W

Desc 1: Washer - Build: XCH

Desc 2: 1/4" x 1" O.D.

Qty: 2

Part #: C-5027

Desc 1: Label

Desc 2: Credit Card Logo

Qty: 1

Part #: C-5765-W

Desc 1: Mounting Bracket

Desc 2: 10 Degree - White Finish

Qty: 1

Part #: C-5365

Desc 1: Bypass Harness

Desc 2: Alliance Coin Vault Bypass

Qty: 1

Remove existing coin box and coin drop.
Remove connections to coin vault service switch and bridge connections using C-5365 Bypass Harness.
Install C-5765-W Metercase Bracket over the front of the metercase and secure using the C-1059 Kep Nut, and C-1070-W Washer.

I-M0135

Part #: C-5801

Desc 1: F1 Reader Mounting Kit

Desc 2: Front

Qty: 1

Place the C-5700-TEMP Drill Template on the desired mounting location.
Verify included harnesses will reach desired location without encountering interference from internal machine components.
Refer to FasCard Mounting Guide for further instructions.

Connect Power

I-P0003

Part #: C-5101

Desc 1: Spade Taps

Desc 2: 18-14 AWG

Qty: 3

Part #: C-5210

Desc 1: Power Adapter Harness

Desc 2: CGI

Qty: 1

Part #: C-5500

Desc 1: Power Extension Harness

Desc 2: 25.5"

Qty: 1

Part #: C-5602R1

Desc 1: Power Converter

Desc 2: SMT-012-018VW

Qty: 1

Tap power as described in the Fascard Reader Install - Universal Concepts document using the C-5101 Spade Taps provided.
Connect the C-5210 Power Adapter Harness to the installed spade taps. Connect the opposite end to the C-5602 Power Converter.
Connect the C-5500 Power Extension Harness to the appropriate connector on the C-5602 Power Converter. The remaining cable end connects to the FasCard reader.

I-P0002

Part #: C-6204-40

Desc 1: Power Adapter Harness

Desc 2: F2, 12vDC Pow Harness - 40"

Qty: 1

Connect the C-6204-40 12VDC Power Harness to the H10 connection on the machine control assembly.
1. Secure the green wire beneath the ground screw.
Connect the opposite end of the C-6204-40 Power Adapter Harness (3-pin molex) to the F2 reader.

Connect Coin Sense Harness

Connect Machine Interface Harness

Connect and Mount Reader

Feed remaining harness ends through the mounting hole as described in F1: FasCard Reader Mounting Guide.
Connect the free end of the Machine Start Harness to the appropriate port.
1. For pulse start harnesses (white connector), connect to port 2 (Pulse Connection Port) as shown in the image above.
2. For serial start harnesses (black connector), connect to port 1 (Serial Connection Port) as shown in the image above
Connect the free end of the Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.
Connect the free end of the C-5500 Power Extension Harness to port 4 (Power Harness Connection Port) as shown in the image above.
Secure the FasCard reader to base as described in the F1: FasCard Reader Mounting Guide.

Machine Configuration

ACA machines using a serial configuration require dip switch 3 on the Machine Control Board to be set to the 'ON' position. Leave all other dip switches as is.