3286 Reader Install Guide

Install Mounting Hardware

 I-M0003

Part #: C-6801

Desc 1: F2/F3 Reader Mounting Kit

Desc 2: Universal

   Qty: 1

1. Place the C-6700-TEMP Drill Template on the desired mounting location.

2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

3. Refer to FasCard Mounting Guide for further instructions.

 I-M0108

Part #: C-1042

Desc 1: Nut

Desc 2: 8-32 - Kep

   Qty: 4

Part #: C-5414

Desc 1: F2/F3 Std. Mounting Bracket

Desc 2: Sheet metal base

   Qty: 1

Part #: C-5416

Desc 1: Screw

Desc 2: 8-32" x 3/8" - Button - Torx

   Qty: 2

Part #: C-5420

Desc 1: Screw

Desc 2: 10-32 x ¼" - Pan

   Qty: 2

Part #: C-6903

Desc 1: F2, Bracket

Desc 2: Continental E- Series 30+

   Qty: 1

1. Remove existing coin box and coin drop.

2. Secure C-5414 F2 Mounting Bracket to the C-6903 Mounting Bracket using the (2) C-5420 10-32 x 1/4 Pan Screws.

3. Install the C-6903 Mounting Bracket into the Coin Vault. Use (4) C-1042 Kep Nuts to secure to Coin Vault.

Connect Power

 I-P0007

Part #: C-5101

Desc 1: Spade Taps

Desc 2: 18-14 AWG

   Qty: 2

Part #: C-5336

Desc 1: Power Adapter Harness

Desc 2: Dexter Stack

   Qty: 1

Part #: C-5500

Desc 1: Power Extension Harness

Desc 2: 25.5"

   Qty: 1

Part #: C-5602R1

Desc 1: Power Converter

Desc 2: SMT-012-018VW

   Qty: 1

1. Tap power as described in the Fascard Reader Install - Universal Concepts document using the C-5101 Spade Taps provided.
2. Connect the C-5336 Power Adapter Harness to the installed spade taps- Blue to Black and Brown to Red. Secure the green ground terminal under the bolt on top of the washer drum.
3. Connect the opposite end of the C-5336 Power Adapter Harness to the C-5602 Power Converter.
4. Connect the C-5500 Power Extension Harness to the appropriate connector on the C-5602 Power Converter. The remaining cable end connects to the FasCard reader.

Connect Coin Sense Harness

 I-S0054

Part #: C-6332

Desc 1: Coin Sense Harness (SA)

Desc 2: CGI EM

   Qty: 1

1. Disconnect the Coin Drop from the Machine Control Assembly.
2. Connect the C-6332 Coin Sense Harness to the harness connected to the Coin Drop.
   1. Connect the Red connector to the Coin Acceptor connection, where the coin drop was previously connected, on the Machine Control Assembly.

Connect Machine Interface Harness

 I-T0017

Part #: C-0114-MLV

Desc 1: Machine Start Harness

Desc 2: Continental

   Qty: 1

1. Connect the C-0114-MLV Machine Start Harness to the middle X1 port on the serial communication board.
   

Connect and Mount Reader

1. Feed remaining harness ends through the mounting hole.
2. Connect the free end of the C-0114-MLV Machine Start Harness to port 5 (Serial Connection Port) as shown in the image above.
3. (Coin and Card Installation Only) Connect the free end of the C-6332 Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.
4. Connect the free end of the C-5500 Power Extension Harness to port 1 (Power Harness Connection Port) as shown in the image above.

Machine Configuration

ProfitPlus Controls

1. Connect the washer and open the door. The display will show door.

2. Press and hold down key 1 until the Cod report appears on the display.

3. Enter the access code into the menus by pressing the sequence of eight keys of the code without interruption. In basic configuration (when the machine is delivered) the access code to ADVANCED MODE is: 12341234.

4. If the sequence entered is correct, the display will show Pro, corresponding to the first menu ADVANCED MODE.

5. Keys 2 and 4 allow the selection of the precedent table menus. The menu selected is shown on the display following its keyword. To enter in it, press key 1 when displaying it.

6. Navigate to Mod > ID and set value to '1'.

7. Exit ADVANCE MODE.