Skip to end of banner
Go to start of banner

3529 Reader Install Guide

Skip to end of metadata
Go to start of metadata

You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 3 Next »

Warning!

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses.

It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Overview

Equipment Details

Type: Dryer
Manufacturer: Maytag
Make: Maytag
Model Length: 10

Associated Models


MDG30PC2AL
MDG30PCCWW

Recommended Tools and Supplies

  • Drill

  • 1 1/8" Tungsten Carbide Tipped Hole Cutter

  • Cutting Oil

  • 9/64" Drill Bit

  • Center Punch

  • Hammer

  • Fine Point Permanent Marker

  • Pliers

  • Tape Measure

Installation

Install Mounting Hardware

 I-M0003

Part #: C-6801

Desc 1: F2/F3 Reader Mounting Kit

Desc 2: Universal

   Qty: 1

  1. Place the C-6700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to Touchscreen Reader Mounting Guide (F2 & F3) for further instructions.

 I-M0162

Part #: C-0913

Desc 1: Drop Cover

Desc 2: Maytag Stack Dryer

   Qty: 1

Part #: C-1062

Desc 1: Nut

Desc 2: 4-40 - Kep

   Qty: 4

Part #: C-6801

Desc 1: F2/F3 Reader Mounting Kit

Desc 2: Universal

   Qty: 1

Part #: C-5710

Desc 1: Rubber Grommet

Desc 2: 3/4"

   Qty: 1

  1. Remove existing coin drop.

  2. Install C-0913 Drop Cover where the coin drop was previously installed. Secure in place with C-1062 Kep Nuts.

  3. Place the C-6700-TEMP Drill Template on the desired mounting location.

  4. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  5. Refer to FasCard Mounting Guide for further instructions.

Connect Power

 I-P0012

Part #: C-5101

Desc 1: Spade Taps

Desc 2: 18-14 AWG

   Qty: 3

Part #: C-5210

Desc 1: Power Adapter Harness

Desc 2: CGI

   Qty: 1

Part #: C-5500-60

Desc 1: Power Extension Harness

Desc 2: 60"

   Qty: 1

Part #: C-5602R1

Desc 1: Power Converter

Desc 2: SMT-012-018VW

   Qty: 1

  1. Tap the machine AC power wires using the C-5101 Spade Taps.
    1. For 120v models: L1, N, and Ground wires
    2. For 240v models: L1, L2, and Ground wires
  2. Connect the three wires from the C-5210 Power Adapter Harness to the C-5101 Spade Taps.
    1. Connect the Blue wire to the L1 tap.
    2. Connect the Brown wire to the N/L2 tap.
    3. Connect the Green/Yellow wire to the Ground tap.
  3. Connect the 3-pin connector from the C-5210 Power Adapter Harness to the matching connector on the C-5602R1 Power Converter.
  4. Connect the 4-pin connector from the C-5602R1 Power Converter to the matching connector on the C-5500-60 Power Extension Harness.
  5. Run the C-5500-60 Power Extension Harness to the reader mounting location.

Connect Coin Sense Harness

 I-S0049

Part #: C-6368

Desc 1: Coin Sense Harness (SA)

Desc 2: ADC Phase 7

   Qty: 1

  1. Disconnect the Coin Drop from the Machine Control Assembly.
  2. Connect the C-6368 Coin Sense Harness to the harness connected to the Coin Drop.

Connect Machine Interface Harness

 I-T0067

Part #: C-5369R1

Desc 1: Machine Start Harness

Desc 2: MLG31PC / MDG76PC

   Qty: 1

  1. Connect the C-5369R1 Machine Start Harness to the Coin 1 connector on the Machine Control Assembly.

Connect and Mount Reader

  1. Feed remaining harness ends through the mounting hole.
  2. Connect the free end of the C-5369R1 Machine Start Harness to port 5 (Serial Connection Port) as shown in the image above.
  3. (Coin and Card Installation Only) Connect the free end of the C-6368 Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.
  4. Connect the free end of the C-5500-60 Power Extension Harness to port 1 (Power Harness Connection Port) as shown in the image above.

CCI Software Configuration

Machine ControlPulseSerial

Additional Resources

  • No labels