Skip to end of banner
Go to start of banner

0877 Reader Install Guide

Skip to end of metadata
Go to start of metadata

You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 4 Next »

Warning!

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses.

It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Overview

Equipment Details

Type: Stack Washer/Dryer
Manufacturer: Dexter
Make: Dexter
Model Length: 11

This is the dryer portion of a stacked unit. Will be paired with a washer unit as well.

Associated Models


DSTD30KCS10
DSTD30KCS10TS

Recommended Tools and Supplies

  • Drill

  • 1 1/8" Tungsten Carbide Tipped Hole Cutter

  • Cutting Oil

  • 9/64" Drill Bit

  • Center Punch

  • Hammer

  • Fine Point Permanent Marker

  • Pliers

  • Tape Measure

Installation

Install Mounting Hardware

 I-M0104

Part #: C-5710

Desc 1: Rubber Grommet

Desc 2: 3/4"

   Qty: 1

Part #: C-6801

Desc 1: F2/F3 Reader Mounting Kit

Desc 2: Universal

   Qty: 1

  1. Place the C-6700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to Touchscreen Reader Mounting Guide (F2 & F3) for further instructions.

Connect Power

 I-P0015

Part #: C-5211

Desc 1: Power Adapter Harness

Desc 2: CGI - AC

   Qty: 1

Part #: C-5500-60

Desc 1: Power Extension Harness

Desc 2: 60"

   Qty: 1

Part #: C-5602R1

Desc 1: Power Converter

Desc 2: SMT-012-018VW

   Qty: 1

  1. Tap power as described in the Fascard Reader Install - Universal Concepts document by connecting the C-5211 Power Adapter Harness to the power distribution panel inside the machine.

    1. 120vac: Connect the brown and blue wires to connector #2 closest to outside of machine and #4 on terminal side closest to circuit board.

    2. 240vac: Connect the brown and blue wires to connectors 3 and 5 on the terminal side closest to the circuit board.

    3. Secure the green wire beneath the ground screw.

  2. Connect the opposite end of the C-5211 Power Adapter Harness to the C-5602 Power Converter.

  3. Connect the C-5500-60 Power Extension Harness to the appropriate connector on the C-5602 Power Converter. The remaining cable end connects to the FasCard reader.

Connect Coin Sense Harness

 I-S0031

Part #: C-6253

Desc 1: Coin Sense Harness

Desc 2: 28"

   Qty: 1

  1. Disconnect the Coin Drop from the Machine Control Assembly.

  2. Connect the C-6253 Coin Sense Harness to the microswitch on to the Coin Drop.

Connect Machine Interface Harness

 I-T0038

Part #: C-5254

Desc 1: Machine Start Harness

Desc 2: Dexter Stack Dryer

   Qty: 1

  1. Connect the C-5254 Machine Start Harness to the P2 connector on the Machine Control Assembly.

Connect and Mount Reader

CCI Software Configuration

Machine ControlPulseSerial

Additional Resources

  • No labels