0405 LaundryCard Reader Install Guide

Owned by David Bussman
Last updated: Jan 24, 2024 by Chris Kite
1 min read

Warning!

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses.

It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Overview

Equipment Details

Type: Washer
Manufacturer: Laundrylux
Make: Wascomat
Model Length: 6

Associated Models


W620CC
W625CC
W630CC
W640CC
W645CC
W655CC
W662CC
W675CC
W677
W677CC

Recommended Tools and Supplies

  • Drill

  • 1 1/8" Tungsten Carbide Tipped Hole Cutter

  • Cutting Oil

  • 9/64" Drill Bit

  • Center Punch

  • Hammer

  • Fine Point Permanent Marker

  • Pliers

  • Tape Measure

Installation

Install Mounting Hardware

 I-M0026

Part #: C-0015

Desc 1: Label

Desc 2: Reader Cover Label

   Qty: 1

Part #: C-0141

Desc 1: Screw

Desc 2: 8-32 x 1-1/2" - Cap

   Qty: 2

Part #: C-0922

Desc 1: Mounting Bracket

Desc 2: 6" Angled

   Qty: 1

Part #: C-1059

Desc 1: Nut

Desc 2: 10-32 - Kep

   Qty: 2

  1. Remove existing coin box and coin drop.

  2. Install the C-0922 Mounting Bracket over the coin vault and coin drop opening. Secure to the machine using the (2) C-1059 10-32 keps nuts.

 I-M0025

Part #: C-0015

Desc 1: Label

Desc 2: Reader Cover Label

   Qty: 1

Part #: C-0141

Desc 1: Screw

Desc 2: 8-32 x 1-1/2" - Cap

   Qty: 2

Part #: C-0920R1

Desc 1: Mounting Bracket

Desc 2: 6" Straight w/ studs

   Qty: 1

Part #: C-1059

Desc 1: Nut

Desc 2: 10-32 - Kep

   Qty: 2

  1. Remove existing coin box and coin drop.

  2. Install the C-0920R1 Mounting Bracket over the coin vault and coin drop opening. Secure to the machine using the (2) C-1059 10-32 keps nuts.

Connect Machine Interface Harness

 I-T0073

Part #: C-0126-MLV

Desc 1: Machine Start Harness (SA)

Desc 2: Wascomat Compass

   Qty: 1

Part #: C-5359

Desc 1: Machine Start Harness (SA)

Desc 2: Compass

   Qty: 1

  1. Connect the C-0126-MLV Machine Start Harness to the RS-232 port on the Machine Control Assembly.

  2. Connect the C-5359 Machine Start Harness to the Input 1 port on the Machine Control Assembly.

Connect and Mount Reader

  1. Feed remaining harness ends through the mounting hole.

  2. Connect the free end of the C-5359 Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

  3. Connect the free end of the C-0126-MLV Machine Start Harness to port 1 (Serial Connection Port) as shown in the image above.

  4. Secure the LaundryCard reader to the bracket using C-0141 Screws and cover using C-0015 Label.

CCI Software Configuration

Machine ControlPulseSerial
Compass (Gen6)SingleVend (Relay) / 500msLaundrylux Compass Washer

Additional Resources