Skip to end of banner
Go to start of banner

2077 Reader Install Guide

Skip to end of metadata
Go to start of metadata

You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 3 Next »

Warning!

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses.

It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Overview

Equipment Details

Type: Stack Washer/Dryer
Manufacturer: Dexter
Make: Dexter
Model Length: 22

Dryer Portion of Stack Washer/Dryer.

Associated Models


DCS030NC10EC1XSWBCGUSA
DCS030ND15EC2RSWBCGUSA
DCS030ND15EC2XSWBCGUSX
DCS050ND11EC2RSWBCGUSA
DCS050ND11EC2RSWBCSUSA

Recommended Tools and Supplies

  • Drill

  • 1 1/8" Tungsten Carbide Tipped Hole Cutter

  • Cutting Oil

  • 9/64" Drill Bit

  • Center Punch

  • Hammer

  • Fine Point Permanent Marker

  • Pliers

  • Tape Measure

Installation

Install Mounting Hardware

 I-M0183

Part #: C-6936

Desc 1: F2, Sm Vault Mount Bracket

Desc 2:

   Qty: 1

Part #: C-6801

Desc 1: F2/F3 Reader Mounting Kit

Desc 2: Universal

   Qty: 1

Part #: C-5710

Desc 1: Rubber Grommet

Desc 2: 3/4"

   Qty: 1

Part #: C-0144

Desc 1: Screw

Desc 2: 8-32 x 2" - Flat

   Qty: 2

  1. Remove existing coin box.

  2. Insert the C-5710 Rubber Grommet into the central hole of the C-6936 Vault Bracket.
  3. Run all reader harnesses through coin vault and then the hole of the C-6936 Vault Bracket.

  4. Bend the side tabs of the C-6936 Vault Bracket outward and install into the coin vault. The tabs should snap into place securing the bracket.

  5. Run all reader harnesses through the central hole of the C-5414 Reader Bracket.

  6. Attach the C-5414 Reader Bracket to the C-6936 Vault Bracket using the C-0144 screw.

Connect Power

 I-P0006

Part #: C-5213

Desc 1: Power Adapter Harness

Desc 2: DDAD - AC

   Qty: 1

Part #: C-5500-115

Desc 1: Power Extension Harness

Desc 2: 115"

   Qty: 1

Part #: C-5602R1

Desc 1: Power Converter

Desc 2: SMT-012-018VW

   Qty: 1

  1. Tap power as described in the Fascard Reader Install - Universal Concepts document by connecting the C-5213 Power Adapter Harness to the power distribution terminal block inside the machine.

    1. Connect the black wire to a L1 tab.

    2. Connect the white wire to a L2 tab.

    3. Connect the Green/Yellow wire to the ground tab.

  2. Connect the opposite end of the C-5213 Power Adapter Harness to the C-5602R1 Power Converter.

  3. Connect the C-5500-115 Power Extension Harness to the appropriate connector on the C-5602R1 Power Converter. The remaining cable end connects to the FasCard reader.

Connect Coin Sense Harness

 I-S0034

Part #: C-6258

Desc 1: Coin Sense Harness (SA)

Desc 2: WCAD

   Qty: 1

  1. Disconnect the Coin Drop from the Machine Control Assembly.
  2. Connect the C-6258 Coin Sense Harness to the harness connected to the Coin Drop.

Connect Machine Interface Harness

 I-T0038

Part #: C-5254

Desc 1: Machine Start Harness

Desc 2: Dexter Stack Dryer

   Qty: 1

  1. Connect the C-5257 Machine Start Harness to the P2 connector on the Machine Control Assembly.

Connect and Mount Reader

Item No.ComponentNotes
1Power Connection PortUtilizes the same power harnesses as the first generation FasCard reader.
2Pulse Connection PortConnection point for pulse machine start harnesses.
3Coin 1 Connection PortThis is the connection point for the harness input associated with Coin 1.
4Coin 2 Connection PortThis is the connection point for the harness input associated with Coin 2.
5Serial Connection PortThis is the connection point for serial machine start harnesses.
  1. Feed remaining harness ends through the mounting hole as described in the Touchscreen Reader Mounting Guide (F2 & F3).
  2. Connect the free end of the C-5254 Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.
  3. Connect the free end of the C-6258 Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.
  4. Connect the free end of the C-5500-114 Power Harness to port 1.
  5. Secure the FasCard reader to base as described in the Touchscreen Reader Mounting Guide (F2 & F3).

Machine Configuration

TODO

CCI Software Configuration

Machine ControlPulseSerial
C-Series (1.5)SingleVend (Relay) / 55ms*NOT SUPPORTED*

Additional Resources

  • No labels