Skip to end of banner
Go to start of banner

3449 Reader Install Guide

Skip to end of metadata
Go to start of metadata

You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 3 Next »

Warning!

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses.

It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Overview

Equipment Details

Type: Vending
Manufacturer: Vend-Rite
Make: Vend-Rite
Model Length: Not Set

Machines shipped after Fall 2011 have the newer style white bracket that accepts either a reader or coin mech.

Machines shipped in 2019 or later are not compatible with the C-0972 or C-6972 mounting brackets.

Associated Models

DVM360
VM120BN
VM120C
VM120D
VM120M
VM240
VM240BN
VM240C
VM240D
VM240M
VM360
VM360C
VM360D
VM360DS
VM360M

Recommended Tools and Supplies

  • Drill

  • 1 1/8" Tungsten Carbide Tipped Hole Cutter

  • Cutting Oil

  • 9/64" Drill Bit

  • Center Punch

  • Hammer

  • Fine Point Permanent Marker

  • Pliers

  • Tape Measure

Installation

Install Mounting Hardware

 I-M0117

Part #: C-6972

Desc 1: Vend-Rite 240/360 Mount

Desc 2: Powder coated steel

   Qty: 1

Part #: C-5420

Desc 1: Screw

Desc 2: 10-32 x ¼" - Pan

   Qty: 2

Part #: C-5416

Desc 1: Screw

Desc 2: 8-32" x 3/8" - Button - Torx

   Qty: 2

Part #: C-5414

Desc 1: F2/F3 Std. Mounting Bracket

Desc 2: Sheet metal base

   Qty: 1

  1. Remove existing payment device or payment device bay cover.

  2. Install C-6972 Vend-Rite Mounting Bracket in the payment device bay. Secure in place using factory hardware.
  3. Attach C-5414 Mounting Bracket to the C-6972 Vend-Rite Mounting Bracket using the (2) C-5420 10-32 x 1/4 Pan Screws.

 I-M0174

Part #: C-6801

Desc 1: F2/F3 Reader Mounting Kit

Desc 2: Universal

   Qty: 1

  1. Place the C-6700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to FasCard F2/F3 Reader Installation Guide - Front Mount for further instructions.

Connect Machine Interface Harness

 I-C0020

Part #: C-6124-MDB

Desc 1: Machine Start Harness

Desc 2: F2 MDB Interface Harness

   Qty: 1

  1. Connect the C-6124-MDB Machine Start Harness to the MDB connection on the Machine Control Assembly or to the MDB harness connected to existing payment device.

Connect and Mount Reader

  1. Feed remaining harness ends through the mounting hole as described in the FasCard F2/F3 Reader Installation Guide - Front Mount.
  2. Connect the black, 10-pin connection of the C-6124-MDB Machine Start Harness to port 5 (Serial Connection Port) as shown in the image above.
  3. Connect the clear, 3-pin connection of the C-6124-MDB Power Harness to port 1.
  4. Secure the FasCard reader to base as described in the FasCard F2/F3 Reader Installation Guide - Front Mount.
  • No labels