Skip to end of banner
Go to start of banner

3652 Reader Install Guide

Skip to end of metadata
Go to start of metadata

You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 3 Next »

Warning!

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses.

It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Overview

Equipment Details

Type: Washer
Manufacturer: ONNERA Group
Make: [VARIES]
Model Length: 10

Associated Models


DHU100CHWTOUCHII
DHU25HWTOUCHII
DHU40HWTOUCHII
DHU65HWTOUCHII
DHU80CHWTOUCHII
DLU100CHW
DLU135HW
DLU135HWTOUCHII
DLU25TPSHW
DLU30HWTOUCHII
DLU40HW
DLU40HWTOUCHII
DLU40TPSHW
DLU50HWTOUCHII
DLU60TPSHW
DLU65HW
DLU80CHWTOUCHII
FWH80TP2HW
FWS25TP2HW
FWS30TP2HW
FWS40TP2HW
FWS60TP2HW
FWS80TP2HW

Recommended Tools and Supplies

  • Drill

  • 1 1/8" Tungsten Carbide Tipped Hole Cutter

  • Cutting Oil

  • 9/64" Drill Bit

  • Center Punch

  • Hammer

  • Fine Point Permanent Marker

  • Pliers

  • Tape Measure

Installation

Install Mounting Hardware

 I-M0003

Part #: C-6801

Desc 1: F2/F3 Reader Mounting Kit

Desc 2: Universal

   Qty: 1

  1. Place the C-6700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to F2/F3 Reader Mounting Guide for further instructions.

 I-M0193

Part #: C-6971

Desc 1: FC Mounting Bracket

Desc 2: Fagor Machine

   Qty: 1

Part #: C-5420

Desc 1: Screw

Desc 2: 10-32 x ¼" - Pan

   Qty: 2

Part #: C-5416

Desc 1: Screw

Desc 2: 8-32" x 3/8" - Button - Torx

   Qty: 2

Part #: C-5414

Desc 1: F2/F3 Std. Mounting Bracket

Desc 2: Sheet metal base

   Qty: 1

  1. Remove the existing payment device panel and put aside the fasteners securing the panel in place.

  2. Place the C-5414 Standard Mounting Bracket over the front of the C-6971 FC Mounting Bracket so the three large, circular openings align and attach using the (2) C-5420 10-32 x 1/4" Screws.
  3. Install the C-6971 FC Mounting Bracket into the payment device panel opening. Secure in place using the factory fasteners.

Connect Power

 I-P0012

Part #: C-5101

Desc 1: Spade Taps

Desc 2: 18-14 AWG

   Qty: 3

Part #: C-5210

Desc 1: Power Adapter Harness

Desc 2: CGI

   Qty: 1

Part #: C-5500-60

Desc 1: Power Extension Harness

Desc 2: 60"

   Qty: 1

Part #: C-5602R1

Desc 1: Power Converter

Desc 2: SMT-012-018VW

   Qty: 1

  1. Tap power as described in the Fascard Reader Install - Universal Concepts document by connecting the C-5210 Power Adapter Harness to the power distribution panel inside the machine.

    1. 120vac: Connect the blue wire to L1 and the brown wire to N.

    2. 240vac: Connect the blue wire to L1 and the brown wire to L2.

    3. Connect the green wire to ground.

  2. Connect the opposite end of the C-5210 Power Adapter Harness to the C-5602R1 Power Converter.

  3. Connect the C-5500 Power Extension Harness to the appropriate connector on the C-5602R1 Power Converter. The remaining cable end connects to the FasCard reader.

Connect Coin Sense Harness

 I-S0062

Part #: C-6373

Desc 1: F2 Coin Sense

Desc 2: Coin Sense Harness

   Qty: 1

  1. Disconnect the coin drop 6-pin connection from the machine.
  2. Connect the C-6373 Coin Sense Harness to the coin drop.

Connect Machine Interface Harness

 I-T0091

Part #: C-5374

Desc 1: FC-LC Start Harness

Desc 2: Pulse Start Harness

   Qty: 1

  1. Connect the C-5374 Machine Start Harness to the CN6 6-pin connector used for the coin drop.

Connect and Mount Reader

  1. Feed remaining harness ends through the mounting hole as described in the Touchscreen Reader Mounting Guide (F2 & F3).
  2. Connect the free end of the C-5374 Machine Start Harness to port 5 (Pulse Connection Port) as shown in the image above.
  3. Connect the free end of the C-6373 Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.
  4. Connect the free end of the C-5500 Power Extension Harness to port 1 (Power Harness Connection Port) as shown in the image above.
  5. Secure the FasCard reader to base as described in the Touchscreen Reader Mounting Guide (F2 & F3).

CCI Software Configuration

Machine ControlPulseSerial
Touch IISingleVend (Relay) / 150ms*NOT SUPPORTED*
Touch PlusSingleVend (Relay) / 150ms*NOT SUPPORTED*

Additional Resources

  • No labels