3580 Reader Install Guide

Part #: C-6801

Desc 1: F2/F3 Reader Mounting Kit

Desc 2: Universal

   Qty: 1

1. Place the C-6700-TEMP Drill Template on the desired mounting location.

2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

3. Refer to FasCard Mounting Guide for further instructions.

Part #: C-5801

Desc 1: F1 Reader Mounting Kit

Desc 2: Front

   Qty: 1

1. Place the C-5700-TEMP Drill Template on the desired mounting location.

2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

3. Refer to FasCard Mounting Guide for further instructions.

Part #: C-0141

Desc 1: Screw

Desc 2: 8-32 x 1-1/2" - Cap

   Qty: 2

Part #: C-1059

Desc 1: Nut

Desc 2: 10-32 - Kep

   Qty: 2

Part #: C-1070-W

Desc 1: Washer - Build: XCH

Desc 2: 1/4" x 1" O.D.

   Qty: 2

Part #: C-5027

Desc 1: Label

Desc 2: Credit Card Logo

   Qty: 1

Part #: C-5765-W

Desc 1: Mounting Bracket

Desc 2: 10 Degree - White Finish

   Qty: 1

Part #: C-5365

Desc 1: Bypass Harness

Desc 2: Alliance Coin Vault Bypass

   Qty: 1

1. Remove existing coin box and coin drop/slide.

2. Remove vault service switch connections from the switch and bridge using the C-5365 Bypass Harness.

3. Install C-5765-W Vault Bracket over the metercase opening. Secure in place using C-1059 Kep Nuts and C-1070-W Washers.

   1. If installing on a coin slide equipped model the two holes next to the coin slide bolt will need to be enlarged about a 1/4" to allow the mounting studs to pass through the metercase.

4. Apply C-5027 Label on or near the reader if required for location.

Part #: C-1059

Desc 1: Nut

Desc 2: 10-32 - Kep

   Qty: 2

Part #: C-1070-W

Desc 1: Washer - Build: XCH

Desc 2: 1/4" x 1" O.D.

   Qty: 2

Part #: C-6765-W-R1

Desc 1: F2 Mounting Bracket

Desc 2: 10 Degree - White Finish

   Qty: 1

Part #: C-5365

Desc 1: Bypass Harness

Desc 2: Alliance Coin Vault Bypass

   Qty: 1

Part #: C-5420

Desc 1: Screw

Desc 2: 10-32 x ¼" - Pan

   Qty: 2

Part #: C-5416

Desc 1: Screw

Desc 2: 8-32" x 3/8" - Button - Torx

   Qty: 2

Part #: C-5414

Desc 1: F2/F3 Std. Mounting Bracket

Desc 2: Sheet metal base

   Qty: 1

1. Remove existing coin box and coin drop.

2. Install the C-5365 Bypass Harness by removing the coin vault switch and connecting the spade terminal connections to C-5365 Bypass Harness.

3. Attach the C-5414 F2 Mounting Bracket to the C-6765-W-R1 Metercase Bracket using C-5702 Chase Nipple and C-5703 Lock Nut.

4. Run any card reader harnesses through the coin slot openings and the circular hole in the C-6765-W-R1 Metercase Bracket.

5. Install the C-6765-W-R1 Metercase Bracket so that the two threaded posts insert into the coin drop slots. Then secure it to the machine using the C-1059 Kep Nuts and C-1070-W Washers.

Part #: C-5801

Desc 1: F1 Reader Mounting Kit

Desc 2: Front

   Qty: 1

1. Place the C-5700-TEMP Drill Template on the desired mounting location.

2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

3. Refer to FasCard Mounting Guide for further instructions.

Part #: C-6801

Desc 1: F2/F3 Reader Mounting Kit

Desc 2: Universal

   Qty: 1

1. Place the C-6700-TEMP Drill Template on the desired mounting location.

2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

3. Refer to FasCard Mounting Guide for further instructions.

Part #: C-0940

Desc 1: Vault Cover

Desc 2: 3-7/8" x 2-3/4"

   Qty: 1

Part #: C-5801

Desc 1: F1 Reader Mounting Kit

Desc 2: Front

   Qty: 1

Part #: C-5365

Desc 1: Bypass Harness

Desc 2: Alliance Coin Vault Bypass

   Qty: 1

1. Remove coin drops and coin boxes.

2. Remove vault service switch connections from the switch and bridge using the C-5365 Bypass Harness.

3. Take the C-0940 Vault Cover and bend the inner tabs outward.

4. Insert the C-0940 Vault Cover into the coin box opening. The previously bent tabs should catch the inner lip of the coin vault and secure the bracket in place.

5. Place the C-5700-TEMP Drill Template on the desired mounting location.

6. Verify included harnesses will reach desired location without encountering interference from internal machine components.

   1. Suggested mounting location: Coin drop opening.

7. Refer to FasCard Mounting Guide for further instructions.

Part #: C-6204-40

Desc 1: Power Adapter Harness

Desc 2: F2, 12vDC Pow Harness - 40"

   Qty: 1

1. Connect the C-6204-40 12VDC Power Harness to the H10 Connection on the Machine Control Assembly.

2. Connect the green wire to a chassis ground.

3. The remaining end (3-pin molex) connects directly to the rear of the F2 FasCard Reader.

Part #: C-6207

Desc 1: F2/F3, Alliance ACA Power

Desc 2:

   Qty: 1

1. Connect the 2-pin connector from the C-6207 F2, ACA Power Harness to the 24v transformer behind the front control panel.

2. The remaining end (3-pin molex) connects directly to the rear of the F2 FasCard Reader.

Part #: C-5101

Desc 1: Spade Taps

Desc 2: 18-14 AWG

   Qty: 3

Part #: C-5210

Desc 1: Power Adapter Harness

Desc 2: CGI

   Qty: 1

Part #: C-5500

Desc 1: Power Extension Harness

Desc 2: 25.5"

   Qty: 1

Part #: C-5602R1

Desc 1: Power Converter

Desc 2: SMT-012-018VW

   Qty: 1

1. Tap power as described in the Fascard Reader Install - Universal Concepts document using the C-5101 Spade Taps provided.

2. Connect the C-5210 Power Adapter Harness to the installed spade taps. Connect the opposite end to the C-5602 Power Converter.

3. Connect the C-5500 Power Extension Harness to the appropriate connector on the C-5602 Power Converter. The remaining cable end connects to the FasCard reader.

Part #: C-5250

Desc 1: Coin Sense Harness

Desc 2:

   Qty: 1

1. Disconnect the Coin Drop from the Machine Control Assembly.

2. Connect the C-5250 Coin Sense Harness to the harness connected to the Coin Drop.

Part #: C-5253

Desc 1: Coin Sense Harness

Desc 2: 28"

   Qty: 1

1. Disconnect the Coin Drop from the Machine Control Assembly.

2. Connect the C-5253 Coin Sense Harness to the harness connected to the Coin Drop.

Part #: C-6250

Desc 1: Coin Sense Harness

Desc 2: F2

   Qty: 1

1. Disconnect the Coin Drop from the Machine Control Assembly.

2. Connect the C-6250 Coin Sense Harness to the harness connected to the Coin Drop.

Part #: C-6253

Desc 1: Coin Sense Harness

Desc 2: 28"

   Qty: 1

1. Locate the micro switch on the coin slide assembly for the upper pocket.

2. Disconnect the harness connected to the microswitch and connect C-6253 Coin Sense Harness to the spade tabs on the micro switch.

Part #: C-5300-NC

Desc 1: Machine Start Harness

Desc 2: Aliiance - Normally Closed

   Qty: 1

1. Connect the C-5300-NC Machine Start Harness to the Coin 1 connector on the Machine Control Assembly.

Part #: C-5240

Desc 1: Machine Start Harness

Desc 2: Alliance ACA

   Qty: 1

1. Connect the C-5240 Machine Start Harness to the the H3 connection on the Machine Control Assembly or Communication board.

Part #: C-5256

Desc 1: Machine Start Harns (pulse)

Desc 2: 20" - Male taps, Rq. Female

   Qty: 1

1. Connect the C-5256 Machine Start Harness to the the harness previously connected to the coin slide microswitch spade tabs.

Part #: C-5240

Desc 1: Machine Start Harness

Desc 2: can use C-5240-144

   Qty: 1

Part #: C-6401

Desc 1: Stack Add On Board - MLV

Desc 2: Serial / MultiVend

   Qty: 1

1. Connect the C-5240 Machine Start Harness to the the H3 connection on the Machine Control Assembly or Communication board on the lower pocket control.

Part #: C-5240

Desc 1: Machine Start Harness

Desc 2: can use C-5240-144

   Qty: 1

Part #: C-6250

Desc 1: Coin Sense Harness

Desc 2: can use C-6250-144

   Qty: 1

Part #: C-6401

Desc 1: Stack Add On Board - MLV

Desc 2: Serial / MultiVend

   Qty: 1

1. Connect the C-5240 Machine Start Harness to the the H3 connection on the Machine Control Assembly or Communication board on the lower pocket control.

2. Disconnect the Coin Drop from the Machine Control Assembly lower pocket control.

3. Connect the C-6250 Coin Sense Harness to the harness connected to the lower pocket's Coin Drop.

1. Feed remaining harness ends through mounting bracket.

2. For serial setups:

   1. Connect the free end of the Machine Start Harness to port 1 (Serial Connection Port) as shown in the image above.

   2. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

3. For coin pulse setups:

   1. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

4. Connect the the Cat5 cables running to and from the adjacent machines to ports labeled 3 (Line Connection Ports) as shown in the image above.

5. Secure the LaundryCard reader to the bracketry using included hardware.

1. Feed remaining harness ends through mounting bracket.

2. For serial setups:

   1. Connect the free end of the Machine Start Harness to port 1 (Serial Connection Port) as shown in the image above.

   2. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

3. For coin pulse setups:

   1. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

4. Connect the free end of the Power Harness to port 1.

5. Secure the L2 reader to base as described in FasCard F2/F3 Reader Installation Guide - Front Mount.

1. Feed remaining harness ends through the mounting hole as described in the F1 Reader Mounting Guide.

2. Connect the free end of the Machine Start Harness to port 1 (Serial Connection Port) as shown in the image above.

3. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

4. Connect the free end of the Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.

5. Connect the free end of the Power Extension Harness to port 4 (Power Harness Connection Port) as shown in the image above.

6. Secure the FasCard reader to base as described in the F1 Reader Mounting Guide.

1. Feed remaining harness ends through the mounting hole as described in FasCard F2/F3 Reader Installation Guide - Front Mount.

2. For Serial Setups:

   1. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

   2. Connect the free end of the Machine Start Harness to port 5 (Serial Connection Port) as shown in the image above.

3. For Pulse Setups:

   1. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

4. Connect the free end of the Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.

   1. For dual coin drop setups connect the secondary Coin Sense Harness to port 4 (Coin Sense Harness Connection Port) as shown in the image above.

5. Connect the free end of the Power Harness to port 1.

6. Secure the FasCard reader to base as described in FasCard F2/F3 Reader Installation Guide - Front Mount.

TODO