Skip to end of banner
Go to start of banner

3278 Reader Install Guide

Skip to end of metadata
Go to start of metadata

You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 4 Next »

Warning!

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses.

It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Overview

Equipment Details

Type: Washer
Manufacturer: Dexter
Make: Dexter
Model Length: Not Set

For Fascard Kit# K-5723
There is no terminal block on that machine and the only way to get power is to tap the harness C-5338. The Brown and Blue to two hots and the green to ground. They will need wire taps to do this otherwise they would need a different harness.

Associated Models


WCL25AA
WCL25AB
WCL55AA
WCN18AASS
WCN18ABNS
WCN18ABSS
WCN25AA
WCN25AASS
WCN25AB
WCN25ABNS
WCN25ABSS
WCN40AASS
WCN40ABNS
WCN40ABSS
WCN50ABSS
WCN55AASS
WCN55ABSS

Recommended Tools and Supplies

  • Drill

  • 1 1/8" Tungsten Carbide Tipped Hole Cutter

  • Cutting Oil

  • 9/64" Drill Bit

  • Center Punch

  • Hammer

  • Fine Point Permanent Marker

  • Pliers

  • Tape Measure

Installation

Install Mounting Hardware

 I-M0003

Part #: C-6801

Desc 1: F2/F3 Reader Mounting Kit

Desc 2: Universal

   Qty: 1

  1. Place the C-6700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to FasCard Mounting Guide for further instructions.

Connect Power

 I-P0001

Part #: C-5602R1

Desc 1: Power Converter

Desc 2: SMT-012-018VW

   Qty: 1

Part #: C-5500

Desc 1: Power Extension Harness

Desc 2: 25.5"

   Qty: 1

Part #: C-5338

Desc 1: Power Adapter Harness

Desc 2: WCAD

   Qty: 1

  1. Tap power as described in the Fascard Reader Install - Universal Concepts document by connecting the C-5338 Power Adapter Harness to the power distribution panel inside the machine or tapping as needed.

    1. 120vac- Connect Brown and Blue wires to connector #2 closest to outside of machine and #4 on terminal side closest to circuit board.

    2. 240vac- Connect Brown and Blue wires to connectors 3 and 5 on the terminal side closest to the circuit board.

    3. Secure the green wire beneath the ground screw.

  2. Connect the opposite end of the C-5338 Power Adapter Harness to the C-5602 Power Converter.

  3. Connect the C-5500 Power Extension Harness to the appropriate connector on the C-5602 Power Converter. The remaining cable end connects to the FasCard reader.

Connect Coin Sense Harness

 I-S0031

Part #: C-6253

Desc 1: Coin Sense Harness

Desc 2: 28"

   Qty: 1

  1. Disconnect the Coin Drop from the Machine Control Assembly.

  2. Connect the C-6253 Coin Sense Harness to the harness connected to the Coin Drop.

 I-S0050

Part #: C-6382

Desc 1: Coin Sense Harness

Desc 2: Imonex EM100/EM3

   Qty: 1

  1. Disconnect the Coin Drop from the Machine Control Assembly.

  2. Connect the C-6382 Coin Sense Harness to the harness connected to the Coin Drop.

Connect Machine Interface Harness

 I-T0040

Part #: C-5256

Desc 1: Machine Start Harns (pulse)

Desc 2: 20" - Male taps, Rq. Female

   Qty: 1

  1. Connect the C-5256 Machine Start Harness to the factory coin drop harness previously connected to the microswitch.

Connect and Mount Reader

Item No.

Component

Notes

1

Power Connection Port

Utilizes the same power harnesses as the first generation FasCard reader.

2

Pulse Connection Port

Connection point for pulse machine start harnesses.

3

Coin 1 Connection Port

This is the connection point for the harness input associated with Coin 1.

4

Coin 2 Connection Port

This is the connection point for the harness input associated with Coin 2.

5

Serial Connection Port

This is the connection point for serial machine start harnesses.

  1. Feed remaining harness ends through the mounting hole as described in the F2: FasCard Reader Mounting Guide.

  2. Connect the free end of the C-5256 Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

  3. Connect the free end of the Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.

  4. Connect the free end of the C-5500 Power Harness to port 1.

  5. Secure the FasCard reader to base as described in the FasCard Mounting Guide.

Machine Configuration

TODO

CCI Software Configuration

Machine ControlPulseSerial
A-Series (1.0)SingleVend (Relay) / 150ms*NOT SUPPORTED*

Additional Resources

  • No labels