Skip to end of banner
Go to start of banner

3563 Reader Install Guide

Skip to end of metadata
Go to start of metadata

You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 4 Next »

Warning!

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses.

It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Overview

Equipment Details

Type: Washer
Manufacturer: Maytag
Make: Maytag
Model Length: 10 to 12

Associated Models

MYR20PDA23
MYR20PDT00
MYR20PDT0000
MYR20PDW0000
MYR30PDT0000
MYR30PDW0000
MYR30PDWATS
MYR30PRU0000
MYR30PRW0000
MYR40PDT0000
MYR40PRT0000
MYR55PDCTS
MYR55PDT00
MYR55PDT0000

Recommended Tools and Supplies

  • Drill

  • 1 1/8" Tungsten Carbide Tipped Hole Cutter

  • Cutting Oil

  • 9/64" Drill Bit

  • Center Punch

  • Hammer

  • Fine Point Permanent Marker

  • Pliers

  • Tape Measure

Installation

Install Mounting Hardware

 I-M0152

Part #: C-0913

Desc 1: Drop Cover

Desc 2: Maytag Stack Dryer

   Qty: 1

Part #: C-6801

Desc 1: F2/F3 Reader Mounting Kit

Desc 2: Universal

   Qty: 1

Part #: C-1062

Desc 1: Nut

Desc 2: 4-40 - Kep

   Qty: 4

Part #: C-6936

Desc 1: F2, Sm Vault Mount Bracket

Desc 2:

   Qty: 1

Part #: C-5751

Desc 1: Screw

Desc 2: 8-32 x 2-1/2" - Flat

   Qty: 2

  1. Remove existing coin box and coin drop.

  2. Install the C-0913 Drop Cover in the coin drop opening and secure using the C-1062 Keps Nuts.

  3. Run all reader harnesses through coin vault and then the hole of the C-6936 Vault Bracket.

  4. Bend the side tabs of the C-6936 Vault Bracket outward and install into the coin vault. The tabs should snap into place securing the bracket.

  5. Run all reader harnesses through the central hole of the C-5414 Reader Bracket.

  6. Attach the C-5414 Reader Bracket to the C-6936 Vault Bracket using the C-0144 screw so that it is flush with the front panel.

Connect Power

 I-P0003

Part #: C-5101

Desc 1: Spade Taps

Desc 2: 18-14 AWG

   Qty: 3

Part #: C-5210

Desc 1: Power Adapter Harness

Desc 2: CGI

   Qty: 1

Part #: C-5500

Desc 1: Power Extension Harness

Desc 2: 25.5"

   Qty: 1

Part #: C-5602R1

Desc 1: Power Converter

Desc 2: SMT-012-018VW

   Qty: 1

  1. Use the C-5101 Spade Taps on the incoming power.

    1. Tap the L1 wire.

    2. Tap the N / L2 wire.

    3. Tap the Ground wire.

  2. Take the C-5210 Power Adapter Harness and connect the red tab connectors to the following wires:

    1. Connect the blue wire to the L1 wire.

    2. Connect the brown wire to the N / L2 wire.

    3. Connect the green/yellow wire to the Ground wire.

  3. Connect the 3-pin connector from the C-5210 Power Adapter Harness to the matching connection on the C-5602R1 Power Converter.

  4. Connect the 4-pin connector from the C-5602R1 Power Converter to the matching connection on the C-5500 Power Extension Harness.

Connect Coin Sense Harness

Connect Machine Interface Harness

 I-T0088

Part #: C-5370

Desc 1: Machine Start Harness

Desc 2: MayTag 8pin

   Qty: 1

  1. Connect the C-5370 Machine Start Harness to the 8-pin J6 harness connection accessible near the coin drop.

    maytag-myr-mys-j6-8pin-20240125-043130.png

Connect and Mount Reader

 LaundryCard Reader (C-0100, C-0101, C-0102, C-0103)

  1. Feed remaining harness ends through mounting bracket.

  2. For serial setups:

    1. Connect the free end of the Machine Start Harness to port 1 (Serial Connection Port) as shown in the image above.

    2. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

  3. For coin pulse setups:

    1. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

  4. Connect the the Cat5 cables running to and from the adjacent machines to ports labeled 3 (Line Connection Ports) as shown in the image above.

  5. Secure the LaundryCard reader to the bracketry using included hardware.

 LaundryCard L2 Reader (C-0103-L2)

L2_Port_Guide.png

  1. Feed remaining harness ends through mounting bracket.

  2. For serial setups:

    1. Connect the free end of the Machine Start Harness to port 1 (Serial Connection Port) as shown in the image above.

    2. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

  3. For coin pulse setups:

    1. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

  4. Connect the free end of the Power Harness to port 1.

  5. Secure the L2 reader to base as described in FasCard F2/F3 Reader Installation Guide - Front Mount.

 F1 Reader (C-5001)

  1. Feed remaining harness ends through the mounting hole as described in the F1 Reader Mounting Guide.

  2. Connect the free end of the Machine Start Harness to port 1 (Serial Connection Port) as shown in the image above.

  3. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

  4. Connect the free end of the Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.

  5. Connect the free end of the Power Extension Harness to port 4 (Power Harness Connection Port) as shown in the image above.

  6. Secure the FasCard reader to base as described in the F1 Reader Mounting Guide.

 F2/FLEX Reader (C-5401, C-5402, C-5402E)

  1. Feed remaining harness ends through the mounting hole as described in FasCard F2/F3 Reader Installation Guide - Front Mount.

  2. For Serial Setups:

    1. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

    2. Connect the free end of the Machine Start Harness to port 5 (Serial Connection Port) as shown in the image above.

  3. For Pulse Setups:

    1. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

  4. Connect the free end of the Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.

    1. For dual coin drop setups connect the secondary Coin Sense Harness to port 4 (Coin Sense Harness Connection Port) as shown in the image above.

  5. Connect the free end of the Power Harness to port 1.

  6. Secure the FasCard reader to base as described in FasCard F2/F3 Reader Installation Guide - Front Mount.

 F3 Reader (C-5520, C-5520E)

TODO

Machine Configuration

  1. Enter Service Mode and navigate to J option.

  2. Set option to J.d.

  3. Exit Service Mode.

CCI Software Configuration

Machine ControlPulseSerial
Gen1SingleVend (MLV+) / 24ms*NOT SUPPORTED*

Additional Resources

  • No labels