2036 F1 Reader Install Guide

Owned by Brett Norrell (Deactivated)
Last updated: Jan 23, 2024 by Chris Kite
2 min read

Warning!

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses.

It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Overview

Equipment Details

Type: Tumble Dryer (Stack)
Manufacturer: ADC
Make: ADC
Model Length: Not Set

Associated Models


AD236
AD236D
ADC236
ADG236
ADG236D

Recommended Tools and Supplies

  • Drill

  • 1 1/8" Tungsten Carbide Tipped Hole Cutter

  • Cutting Oil

  • 9/64" Drill Bit

  • Center Punch

  • Hammer

  • Fine Point Permanent Marker

  • Pliers

  • Tape Measure

Installation

Install Mounting Hardware

Connect Power

 I-P0012

Part #: C-5101

Desc 1: Spade Taps

Desc 2: 18-14 AWG

   Qty: 3

Part #: C-5210

Desc 1: Power Adapter Harness

Desc 2: CGI

   Qty: 1

Part #: C-5500-60

Desc 1: Power Extension Harness

Desc 2: 60"

   Qty: 1

Part #: C-5602R1

Desc 1: Power Converter

Desc 2: SMT-012-018VW

   Qty: 1

  1. Tap power as described in the Fascard Reader Install - Universal Concepts document using the C-5101 Spade Taps provided.

  2. Connect the C-5210 Power Adapter Harness to the installed spade taps. Connect the opposite end to the C-5602 Power Converter.

  3. Connect the C-5500-60 Power Extension Harness to the appropriate connector on the C-5602 Power Converter. The remaining cable end connects to the FasCard reader.

Connect Coin Sense Harness

 I-S0012

Part #: C-5343

Desc 1: Coin Sense Harness (SA)

Desc 2: ADC Phase 5

   Qty: 1

  1. Disconnect the Coin Drop from the Machine Control Assembly.

  2. Connect the C-5343 Coin Sense Harness to the harness connected to the Coin Drop.

 I-S0022

Part #: C-5368

Desc 1: Coin Sense Harness

Desc 2: ADC Phase 7

   Qty: 1

  1. Disconnect the Coin Drop from the Machine Control Assembly.

  2. Connect the C-5368 Coin Sense Harness to the harness connected to the Coin Drop.

Connect Machine Interface Harness

 I-T0056

Part #: C-5344

Desc 1: Machine Start Harness

Desc 2: ADC Phase 5

   Qty: 1

  1. Connect the C-5344 Machine Start Harness to the Coin 1 connection on the Machine Control Assembly.

 I-T0057

Part #: C-5345

Desc 1: Machine Start Harness

Desc 2: ADC Phase 7

   Qty: 1

  1. Connect the C-5345 Machine Start Harness to the Coin 1 connection on the Machine Control Assembly.

Connect and Mount Reader

  1. Feed remaining harness ends through the mounting hole as described in the F1 Reader Install Guide.

  2. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

  3. Connect the free end of the Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.

  4. Connect the free end of the C-5500-60 Power Extension Harness to port 4 (Power Harness Connection Port) as shown in the image above.

  5. Secure the FasCard reader to base as described in the FasCard Mounting Guide.

Machine Configuration

TODO