3275 LaundryCard Reader Install Guide

Owned by Brett Norrell (Deactivated)
Last updated: Jan 23, 2024 by Chris Kite
1 min read
ERROR: Equipment ID 3275 does not exist.

Install Mounting Hardware

 I-M0020

Part #: C-0015

Desc 1: Label

Desc 2: Reader Cover Label

   Qty: 1

Part #: C-0031

Desc 1: Label

Desc 2: Dexter Instruction Panel

   Qty: 1

Part #: C-0133

Desc 1: Standoff

Desc 2: 8-32" x 1-1/2" - Hex

   Qty: 2

Part #: C-0140

Desc 1: Screw

Desc 2: 8-32 x 3/4" - Cap

   Qty: 2

Part #: C-0906

Desc 1: Spacer Plate

Desc 2: 5 1/2" x 4 3/8"

   Qty: 1

Part #: C-0936

Desc 1: Vault Mount Bracket

Desc 2:

   Qty: 1

Part #: C-0963

Desc 1: Drop Cover

Desc 2: 2-3/8" x 4-5/8" - Black

   Qty: 1

Part #: C-1062

Desc 1: Nut

Desc 2: 4-40 - Kep

   Qty: 4

  1. Remove existing coin box.

  2. Bend the side tabs of the C-0936 Bracket outward and install into the coin vault. The tabs should snap into place securing the bracket.

  3. Attach the C-0133 Standoffs to the Bracket.

  4. Place the C-0906 spacer between the reader and the machine's panel.

  5. Remove any existing coin drop.

  6. Mount the C-0963 Drop Cover using C-1062 Kep Nuts.

  7. Affix C-0031 Label to the C-0963 Drop Cover.

 I-M0023

Part #: C-0015

Desc 1: Label

Desc 2: Reader Cover Label

   Qty: 1

Part #: C-0031

Desc 1: Label

Desc 2: Dexter Instruction Panel

   Qty: 1

Part #: C-0906

Desc 1: Spacer Plate

Desc 2: 5 1/2" x 4 3/8"

   Qty: 1

Part #: C-0970R1

Desc 1: Revised Mounting Bracket

Desc 2: Multi-Purpose

   Qty: 1

Part #: C-5751

Desc 1: Screw

Desc 2: 8-32 x 2-1/2" - Flat

   Qty: 2

  1. Apply C-0031 Label to cover the Easy Card slot.

  2. Using the C-0970R1 Mounting Bracket, mark out cutting lines on the front panel of the machine near where a coin vault would normally be mounted. Mark the central opening, along with the two threaded holes to the sides of the central opening.

  3. Place the C-0970R1 Mounting Bracket on the inside of the panel, and C-0906 Spacer on the outside of the panel. Then secure all components and reader in place using C-5751 Screws.

Connect Machine Interface Harness

 I-T0040

Part #: C-5256

Desc 1: Machine Start Harns (pulse)

Desc 2: 20" - Male taps, Rq. Female

   Qty: 1

  1. Connect the C-5256 Machine Start Harness to the Coin 1 terminal connections previously connected to the micro switch on the coin drop.

 I-T0001

Part #: C-0127

Desc 1: Machine Start Harness

Desc 2: Dexter FL

   Qty: 1

  1. Connect the C-0127 Machine Start Harness to the P2 connector on the Machine Control Assembly.

Connect and Mount Reader

  1. Feed remaining harness ends through mounting bracket.

  2. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

  3. Connect the the Cat5 cables running to and from the adjacent machines to ports labeled 3 (Line Connection Ports) as shown in the image above.

  4. Secure the LaundryCard reader to the bracket using included hardware.

Machine Configuration

TODO

ERROR: Equipment ID 3275 does not exist.