Page Comparison

Cci readerinstall header

Cci readerinstall kit

KitID	841
KitDesc	Coin and Card

Place the C-6700-TEMP Drill Template on the desired mounting location.
Verify included harnesses will reach desired location without encountering interference from internal machine components.
Refer to for further instructions.

Cci readerinstall kit

KitID	854
KitDesc	Card Only

Remove existing coin box.
Bend the side tabs of the C-0941 Vault Cover outward and install into the coin vault. The tabs should snap into place securing the bracket.
Place the C-6700-TEMP Drill Template on the desired mounting location.
Verify included harnesses will reach desired location without encountering interference from internal machine components.
Refer to for further instructions.

Cci readerinstall kit

KitID	0
KitDesc	Change Me

Tap power as described in the document by connecting the C-5101 Power Adapter Harness to the power distribution panel inside the machine.
1. 120vac: Connect the brown and blue wires to connector #2 closest to outside of machine and #4 on terminal side closest to circuit board.
2. 240vac: Connect the brown and blue wires to connectors 3 and 5 on the terminal side closest to the circuit board.
3. Secure the green wire beneath the ground screw.
Connect the opposite end of the C-5101 Power Adapter Harness to the C-5602 Power Converter.
Connect the C-5500-84 Power Extension Harness to the appropriate connector on the C-5602 Power Converter. The remaining cable end connects to the FasCard reader.

Cci readerinstall kit

KitID	716
KitDesc	Coin Drop: Factory Edge Connector

Disconnect the Coin Drop from the Machine Control Assembly.
Connect the C-6357 Coin Sense Harness to the harness connected to the Coin Drop.

Cci readerinstall kit

KitID	718
KitDesc	Coin Drop: Factory Terminal Connector

Disconnect the Coin Drop from the Machine Control Assembly.
Connect the C-6358 Coin Sense Harness to the harness connected to the Coin Drop.
1. Connect the coin drop wires to the matching colored wires on the coin sense harness.

Cci readerinstall kit

KitID	655
KitDesc	Pulse - Edge Connector

Connect the C-5353R1 Machine Start Harness to the Coin 1 connector on the Machine Control Assembly.

Cci readerinstall kit

KitID	659
KitDesc	Pulse - Terminal Connector

Connect the C-5356 Machine Start Harness to the Positions 2 and 3 on the terminal block.

Cci readerinstall kit

KitID	830
KitDesc	Pulse - Terminal Connector with Block

Attach the C-5313 Terminal Block to the Machine Control Assembly.
Connect the C-5356 Machine Start Harness to the Positions 2 and 3 on the terminal block.
1. Terminal block positions are numbered 0-6. Position 0 is closest to the board edge.

Multiexcerpt include

Item No.	Component	Notes
1	Power Connection Port	Utilizes the same power harnesses as the first generation FasCard reader.
2	Pulse Connection Port	Connection point for pulse machine start harnesses.
3	Coin 1 Connection Port	This is the connection point for the harness input associated with Coin 1.
4	Coin 2 Connection Port	This is the connection point for the harness input associated with Coin 2.
5	Serial Connection Port	This is the connection point for serial machine start harnesses.

Feed remaining harness ends through the mounting hole as described in the F2/F3: FasCard Reader Mounting Guide.
Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.
Connect the free end of theCoin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.
Connect the free end of the C-5500-84 Power Harness to port 1.
Secure the FasCard reader to base as described in the FasCard Mounting Guide.

TODO

Cci readerinstall footer

Versions Compared