Skip to end of banner
Go to start of banner

0394 Reader Install Guide

Skip to end of metadata
Go to start of metadata

You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 3 Next »

Warning!

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses.

It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Overview

Equipment Details

Type: Tumble Dryer (Stack)
Manufacturer: Laundrylux
Make: Wascomat
Model Length: 6

FasCard Coin & Card kit depends on how the coin drop is connected to the dryer computer.

Associated Models


TD3030
TD30x30
TD3535
TD4040
TD4545
TD45X45

Recommended Tools and Supplies

  • Drill

  • 1 1/8" Tungsten Carbide Tipped Hole Cutter

  • Cutting Oil

  • 9/64" Drill Bit

  • Center Punch

  • Hammer

  • Fine Point Permanent Marker

  • Pliers

  • Tape Measure

Installation

Install Mounting Hardware

 I-M0104

Part #: C-5710

Desc 1: Rubber Grommet

Desc 2: 3/4"

   Qty: 1

Part #: C-6801

Desc 1: F2/F3 Reader Mounting Kit

Desc 2: Universal

   Qty: 1

  1. Place the C-6700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to FasCard Mounting Guide for further instructions.

 I-M0116

Part #: C-6801

Desc 1: F2/F3 Reader Mounting Kit

Desc 2: Universal

   Qty: 1

Part #: C-0941

Desc 1: Vault Cover

Desc 2: 3-7/8" x 3-1/2"

   Qty: 1

Part #: C-5710

Desc 1: Rubber Grommet

Desc 2: 3/4"

   Qty: 1

Part #: C-0907

Desc 1: Drop Cover

Desc 2: Wascomat TD 3030

   Qty: 1

Part #: C-1062

Desc 1: Nut

Desc 2: 4-40 - Kep

   Qty: 4

Part #: C-0136

Desc 1: Screw

Desc 2: 4-40 1/2" pan head zinc

   Qty: 4

  1. Remove existing coin box.

  2. Bend the side tabs of the C-0941 Vault Cover outward and install into the coin vault. The tabs should snap into place securing the bracket.

  3. Place the C-6700-TEMP Drill Template on the desired mounting location.

  4. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  5. Refer to FasCard Mounting Guide for further instructions.

Connect Power

Kit 0 does not exist

Connect Coin Sense Harness

 I-S0043

Part #: C-6357

Desc 1: Coin Sense Harness (SA)

Desc 2: LaundryLux Edge Connector

   Qty: 1

  1. Disconnect the Coin Drop from the Machine Control Assembly.
  2. Connect the C-6357 Coin Sense Harness to the harness connected to the Coin Drop.
 I-S0045

Part #: C-6358

Desc 1: Coin Sense Harness (SA)

Desc 2: TD

   Qty: 1

  1. Disconnect the Coin Drop from the Machine Control Assembly.
  2. Connect the C-6358 Coin Sense Harness to the harness connected to the Coin Drop.
    1. Connect the coin drop wires to the matching colored wires on the coin sense harness.

Connect Machine Interface Harness

 I-T0059

Part #: C-5353R1

Desc 1: Machine Start Harness (SA)

Desc 2: 40" - LaundryLux

   Qty: 1

  1. Connect the C-5353R1 Machine Start Harness to the Coin 1 connector on the Machine Control Assembly.
 I-T0063

Part #: C-5356

Desc 1: Machine Start Harns (rare)

Desc 2: TD

   Qty: 1

  1. Connect the C-5356 Machine Start Harness to the Positions 2 and 3 on the terminal block.
 I-T0075

Part #: C-5313

Desc 1: Terminal Block

Desc 2: for Laundrylux TD Dryers

   Qty: 1

Part #: C-5356

Desc 1: Machine Start Harns (rare)

Desc 2: TD

   Qty: 1

  1. Attach the C-5313 Terminal Block to the Machine Control Assembly.
  2. Connect the C-5356 Machine Start Harness to the Positions 2 and 3 on the terminal block.
    1. Terminal block positions are numbered 0-6. Position 0 is closest to the board edge.

Connect and Mount Reader

Item No.ComponentNotes
1Power Connection PortUtilizes the same power harnesses as the first generation FasCard reader.
2Pulse Connection PortConnection point for pulse machine start harnesses.
3Coin 1 Connection PortThis is the connection point for the harness input associated with Coin 1.
4Coin 2 Connection PortThis is the connection point for the harness input associated with Coin 2.
5Serial Connection PortThis is the connection point for serial machine start harnesses.
  1. Feed remaining harness ends through the mounting hole as described in the F2/F3: FasCard Reader Mounting Guide.
  2. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.
  3. Connect the free end of theCoin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.
  4. Connect the free end of the C-5500-84 Power Harness to port 1.
  5. Secure the FasCard reader to base as described in the FasCard Mounting Guide.

Machine Configuration

TODO

CCI Software Configuration

Machine ControlPulseSerial

Additional Resources

  • No labels