Versions Compared

Old Version 2

changes.mady.by.user Chris Kite

Saved on

compared with

New Version 3

changes.mady.by.user CCI Integration User

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Cci readerinstall header

Install Mounting Hardware

Cci readerinstall kit
KitID584
KitDescCoin and Card

  1. Place the C-6700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to for further instructions.

Cci readerinstall kit
KitID863
KitDescCard Only

  1. Remove existing coin box.

  2. Remove Vault Switchand bridge the wires previously connected to the Vault Switchwith the C-5365 Bypass Harness.

  3. Bend the side tabs of theC-6602Vault Bracketoutward and install into the coin vault. The tabs should snap into place securing the bracket.

  4. Arrange both the C-5414 Mounting Bracket and the C-0906 Spacer so the smaller screw holes align. Secure both to the C-6601 Vault Mount so that the C-0906 Spacer is between the machine panel and the C-5414 Mounting Bracket.
  5. Apply the C-5033 Label over the coin drop opening.

Connect Power

Cci readerinstall kit
KitID663

  1. Tap power as described in the document by connecting theC-5336Power Adapter Harnessto the power distribution panel inside the machine.

    1. 120vac: Connect the blue wire to L1 and the brown wire to N using theC-5101Spade Taps.

    2. 240vac: Connect the blue wire to L1 and the brown wire to L2 using theC-5101Spade Taps.

    3. Secure the green wire beneath the ground screw.

  2. Connect the opposite end of theC-5336Power Adapter Harnessto theC-5602R1Power Converter.

  3. Connect theC-5500Power Extension Harness to the appropriate connector on theC-5602R1Power Converter. The remaining cable end connects to the FasCard reader.

Connect Coin Sense Harness

Cci readerinstall kit
KitID719
KitDescCoin Drop: Factory
  1. Disconnect the terminal quick connects from the terminal block mounted on top of the coin vault.
    1. Mark the outer green and red quick connects for later use if using C-5265 Machine Start Harness.
  2. Connect the C-6360 Coin Sense Harness to the terminal block tabs. Match each connection by color of the coin sensor wires.

Connect Machine Interface Harness

Cci readerinstall kit
KitID984
KitDescPulse
  1. Connect the red wires from the C-5265 Machine Start Harness to the red and green terminal quick connects from the terminal block mounted on the coin vault. Pairing does not matter.
  2. Run the black wires from the C-5265 Machine Start Harness to the SoapLink 24v relay board located on the back of the machine.
  3. Connect black wires from the C-5265 Machine Start Harnessto RO1 and JO1. Pairing does not matter. (See below image for reference.)
  4. Connect the ends of C-5266 Jumper to RO11 and QO3. (See below image for reference.)

Connect and Mount Reader

Multiexcerpt include
SpaceWithExcerptCCIDOC
MultiExcerptNameF2 Reader
PageWithExcerpt_Reader Ports

Item No.ComponentNotes
1Power Connection PortUtilizes the same power harnesses as the first generation FasCard reader.
2Pulse Connection PortConnection point for pulse machine start harnesses.
3Coin 1 Connection PortThis is the connection point for the harness input associated with Coin 1.
4Coin 2 Connection PortThis is the connection point for the harness input associated with Coin 2.
5Serial Connection PortThis is the connection point for serial machine start harnesses.
  1. Feed remaining harness ends through the mounting hole as described in the Touchscreen Reader Mounting Guide (F2 & F3).
  2. Connect the free end of the C-5265 Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.
  3. Connect the free end of the C-6360 Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.
  4. Connect the free end of the C-5500 Power Harness to port 1.
  5. Secure the FasCard reader to base as described in the Touchscreen Reader Mounting Guide (F2 & F3).

Machine Configuration

Singlevend - Coin Pulse

  1. Enter the machine's System Menu and set the following settings (See machine programming manual for more info.)
    1. Machine Settings
      1. Liquid Soap Supply: Enabled
    2. Payment Settings:
      1. Enable Types: Disable all payment types
      2. Coin Options: Single
      3. Coin 1 Value: Intended Vend Price
      4. Coin 2 Value: Intended Vend Price
      5. Serial Payment System: Disabled
  2. On the FasCard Admin site, create a SingleVend equipment type with the following settings:
    1. Mode: Simple
    2. Pulse Length: 1000
    3. Pulse Interval: 250
    4. Pulse Type: Relay
    5. Sensor Input: Required Off
    6. Show Remaining Time: Disabled
    7. Cycle Time: 600 Seconds
    8. # Pulses: 1

Multiexcerpt fast include inline macro
nameMidas
templateDataeJyLjgUAARUAuQ==
page_Machine Configuration
addpanelfalse

Cci readerinstall footer