Versions Compared

Old Version 5

changes.mady.by.user CCI Integration User

Saved on

compared with

New Version 6

changes.mady.by.user Chris Kite

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Cci readerinstall header

Install Mounting Hardware

  • Place the C-0801 Mounting Bracket at the desired mounting location. Align the bracket so the two unthreaded holes are at the top and bottom of the bracket.
  • Using the C-0801 Mounting Bracket, mark the top and bottom holes for mounting it to the surface. Then mark the large central opening for inserting the LaundryCard reader and running required harnesses.
    • Cut open the large central opening in the surface, then use material appropriate fasteners (Not Provided.) to secure the C-0801 Mounting Bracket to the surface.
    cci-readerinstall-kit
    KitID745
    KitDescSurface Mount - Door Strike
    step
    componentMounting

    Place the C-5700-TEMP Drill Templateon the desired mounting location.Mark hole"D"for the pilot hole to run the harnesses to the reader. Mark"C"and"E"holes to provide mounting points for the reader bracket.Use a1-1/8" hole sawto drill a hole at position"D".Place and align C-5700F1 Mounting Bracketso that the center hole aligns with hole "D" and the two holes immediately to the left and right align with the holes marked for "C" and "E".
  • Using material appropriate fasteners (Not Provided.), secure the C-5700 F1 Mounting Bracket to the surface using points "C" and "E".
  • Optional: If accepting credit cards, apply the C-5027 Label on or near the F1 card reader for applicable credit cards.
    • Place the C-6700-TEMP Drill Templateon the desired mounting location.Mark hole"C"for the pilot hole to run the harnesses to the reader. Mark"D"and"E"holes to provide mounting points for the reader bracket.Use a1-1/8" hole sawto drill a hole at position"C".Place and align C-5414F2 Mounting Bracketso that the center hole aligns with hole "C" and the two holes immediately to the left and right align with the holes marked for "D" and "E".
  • Using material appropriate fasteners (Not Provided.), secure the C-5414 F2 Mounting Bracket to the surface using points "D" and "E".
    • cci-readerinstall-kit
    KitID780
    KitDescSurface Mount - Door Strike
    Cci readerinstall kit
    KitID847
    KitDescSurface Mount - Door Strike

    Connect Power

    Connect the C-5200-72 Powerline Adapter Harnessto an 120v electrical outlet.Connect the white, 3-pin connector from the C-5200-72 Powerline Adapter Harnessto the matching end on the C-5602R1 Power Converter.Connect the 4-pin connector from theC-5500 Power Extension Harnessto the matching end on the C-5602R1 Power Converter.
    Cci readerinstall kit
    KitID801
    KitDesc120v Wall Power
    step
    componentPower

    Connect Machine Interface Harness

    Cci readerinstall kit
    KitID636
    KitDescPulse - Circuit Interruption

    1. Connect the one of the ends of the C-5256 Machine Start Harness to the positive terminal from the door strike power source. Connect the other spade connector to the positive terminal on the door strike.

      1. Note: Depending on the door strike installed, spade terminals may not be available or may be too far apart for the harness to reach. In this case, cut the ends of the C-5256 Machine Start Harness and then cut and splice into the positive lead wire(In any pairing.).

    2. The negative lead from the door strike power source should remain connected to the negative terminal on the door strike.

    3. Note: If the door strike requires a normally closed circuit instead of a normally open one, move the wire in the 6th position to the 4th position on the C-5256 Machine Start Harness.

    trueFasCard Door Strike Wiringfalseautotoptrue4911

    Connect and Mount Reader

    Expand
    titleLaundryCard
    Multiexcerpt include
    SpaceWithExcerptCCIDOC
    MultiExcerptNameLC Reader
    PageWithExcerpt_Reader Ports

  • Feed remaining harness ends through the mounting hole.
    • Connect the free end of theC-5256 Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.Connect the the Cat5 cables running to and from the adjacent machinesto ports labeled 3 (Line Connection Ports) as shown in the image above.

  • Secure the LaundryCard reader to the bracket using included hardware and cover screws using C-0015 Label.

    • Expand
    titleF1 Reader

    Multiexcerpt include
    SpaceWithExcerptCCIDOC
    MultiExcerptNameF1 Reader
    PageWithExcerpt_Reader Ports

  • Feed remaining harness ends through the mounting hole.
    • Connect the free end of theC-5256 Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.
  • Connect the free end of the C-5500 Power Extension Harness to port 4 (Power Harness Connection Port) as shown in the image above.
    • Expand
    titleF2,F3,Flex,FlexRF

    Multiexcerpt include
    SpaceWithExcerptcom.atlassian.confluence.content.render.xhtml.model.resource.identifiers.SpaceResourceIdentifier@7627108f
    MultiExcerptNameF2 Reader
    PageWithExcerpt_Reader Ports

  • Feed remaining harness ends through the mounting hole.
    • Connect the free end of theC-5256 Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.Connect the free end of the C-5500 Power Extension Harness to port 1 (Power Harness Connection Port) as shown in the image above. Cci readerinstall step
    componentReader

    Cci readerinstall footer