Skip to end of banner
Go to start of banner

0114 Reader Install Guide

Skip to end of metadata
Go to start of metadata

You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 5 Next »

Warning!

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses.

It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Overview

Equipment Details

Type: Other
Manufacturer: N/A
Make: [VARIES]
Model Length: Not Set

Associated Models


DOOR

Recommended Tools and Supplies

  • Drill

  • 1 1/8" Tungsten Carbide Tipped Hole Cutter

  • Cutting Oil

  • 9/64" Drill Bit

  • Center Punch

  • Hammer

  • Fine Point Permanent Marker

  • Pliers

  • Tape Measure

Installation

Install Mounting Hardware

 I-M0034

Part #: C-0015

Desc 1: Label

Desc 2: Reader Cover Label

   Qty: 1

Part #: C-0141

Desc 1: Screw

Desc 2: 8-32 x 1-1/2" - Cap

   Qty: 2

Part #: C-0801

Desc 1: Mounting Bracket

Desc 2: Door - painted black

   Qty: 1

  1. Place the C-0801 Mounting Bracket at the desired mounting location. Align the bracket so the two unthreaded holes are at the top and bottom of the bracket.
  2. Using the C-0801 Mounting Bracket, mark the top and bottom holes for mounting it to the surface. Then mark the large central opening for inserting the LaundryCard reader and running required harnesses.
  3. Cut open the large central opening in the surface, then use material appropriate fasteners (Not Provided.) to secure the C-0801 Mounting Bracket to the surface.
 I-M0068

Part #: C-0141

Desc 1: Screw

Desc 2: 8-32 x 1-1/2" - Cap

   Qty: 2

Part #: C-5027

Desc 1: Label

Desc 2: Credit Card Logo

   Qty: 1

Part #: C-5700

Desc 1: Mounting Bracket

Desc 2: Surface Mount

   Qty: 1

  1. Place the C-5700-TEMP Drill Template on the desired mounting location.
  2. Mark hole "D" for the pilot hole to run the harnesses to the reader. Mark "C" and "E" holes to provide mounting points for the reader bracket.
  3. Use a 1-1/8" hole saw to drill a hole at position "D".
  4. Place and align C-5700 F1 Mounting Bracket so that the center hole aligns with hole "D" and the two holes immediately to the left and right align with the holes marked for "C" and "E".
  5. Using material appropriate fasteners (Not Provided.), secure the C-5700 F1 Mounting Bracket to the surface using points "C" and "E".
  6. Optional: If accepting credit cards, apply the C-5027 Label on or near the F1 card reader for applicable credit cards.
 I-M0110

Part #: C-5414

Desc 1: F2/F3 Std. Mounting Bracket

Desc 2: Sheet metal base

   Qty: 1

Part #: C-5416

Desc 1: Screw

Desc 2: 8-32" x 3/8" - Button - Torx

   Qty: 2

  1. Place the C-6700-TEMP Drill Template on the desired mounting location.
  2. Mark hole "C" for the pilot hole to run the harnesses to the reader. Mark "D" and "E" holes to provide mounting points for the reader bracket.
  3. Use a 1-1/8" hole saw to drill a hole at position "C".
  4. Place and align C-5414 F2 Mounting Bracket so that the center hole aligns with hole "C" and the two holes immediately to the left and right align with the holes marked for "D" and "E".
  5. Using material appropriate fasteners (Not Provided.), secure the C-5414 F2 Mounting Bracket to the surface using points "D" and "E".

Connect Power

 I-P0011

Part #: C-5200-72

Desc 1: 72" Power Adapter Harness

Desc 2: 72"

   Qty: 1

Part #: C-5500

Desc 1: Power Extension Harness

Desc 2: 25.5"

   Qty: 1

Part #: C-5602R1

Desc 1: Power Converter

Desc 2: SMT-012-018VW

   Qty: 1

  1. Connect the C-5200-72 Powerline Adapter Harness to an 120v electrical outlet.

  2. Connect the white, 3-pin connector from the C-5200-72 Powerline Adapter Harness to the matching end on the C-5602R1 Power Converter.
  3. Connect the 4-pin connector from the C-5500 Power Extension Harness to the matching end on the C-5602R1 Power Converter.

Connect Machine Interface Harness

 I-T0040

Part #: C-5256

Desc 1: Machine Start Harns (pulse)

Desc 2: 20" - Male taps, Rq. Female

   Qty: 1

  1. Connect the one of the ends of the C-5256 Machine Start Harness to the positive terminal from the door strike power source. Connect the other spade connector to the positive terminal on the door strike.
    1. Note: Depending on the door strike installed, spade terminals may not be available or may be too far apart for the harness to reach. In this case, cut the ends of the C-5256 Machine Start Harness and then cut and splice into the positive lead wire (In any pairing.).
  2. The negative lead from the door strike power source should remain connected to the negative terminal on the door strike.
  3. Note: If the door strike requires a normally closed circuit instead of a normally open one, move the wire in the 6th position to the 4th position on the C-5256 Machine Start Harness.

Connect and Mount Reader

 LaundryCard

  1. Feed remaining harness ends through the mounting hole.
  2. Connect the free end of the C-5256 Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.
  3. Connect the the Cat5 cables running to and from the adjacent machines to ports labeled 3 (Line Connection Ports) as shown in the image above.

  4. Secure the LaundryCard reader to the bracket using included hardware and cover screws using C-0015 Label.


 F1 Reader

  1. Feed remaining harness ends through the mounting hole.
  2. Connect the free end of the C-5256 Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.
  3. Connect the free end of the C-5500 Power Extension Harness to port 4 (Power Harness Connection Port) as shown in the image above.
 F2,F3,Flex,FlexRF

  1. Feed remaining harness ends through the mounting hole.
  2. Connect the free end of the C-5256 Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.
  3. Connect the free end of the C-5500 Power Extension Harness to port 1 (Power Harness Connection Port) as shown in the image above.

CCI Software Configuration

Machine ControlPulseSerial
*NO NAME*SingleVend (Relay) / ANYms*NOT SUPPORTED*

Additional Resources

  • No labels