Page Comparison

Panel

borderColor	#416EB6
titleColor	#ffffff
titleBGColor	#416EB6
title	Overview

This install guide goes over the detailed installation steps for an F2/F3touchscreen FasCard/FLEX reader onto an existing machine in either ahigh-front or top-mount position.

Note

title

C-5402/C-5426-BASE incompatibility

The below solutions are not compatible with previousused high-front/top mount readers or mounting bases.

Warning

title

Swipe Clearance Notice

For top-mount placements, CCI strongly recommends mounting the

frontof

front of the top-mount bracket 1-1/4 inches from the front of the machine,

toallow

to allow for card swipe clearance.

Ensure the drilled hole aligns accordingly. Mounting the top-mount

bracketany

bracket any further back then 1-1/4inches from the front of the machine to the edge of

thereader

the reader can potentially interfere with mounting the reader to the bracket

andmay

and may prevent users from being able to swipe or insert a card into the

readerdue

reader due to lack of clearance.

Required parts & tools

FasCard/FLEX reader

tools

Readers

Bw part list

Parts	C-5401,C-5403,C-5520
ShowDesc2	true
ShowImage	true
ShowDesc1	true

X080-001 (

Kits

Expand

title	Top Mount Kit

)

Cci kits

KitID	I-X0020
ShowKitID	true
ShowKitDesc	true

X080-002 (

Expand

title	High-Front Mount Kit

)

Cci kits

KitID	I-X0021
ShowKitID	true
ShowKitDesc	true

Recommended tools & supplies (not included)

Expand

title	Items not included

Multiexcerpt include

MultiExcerptName	F2 Tools
PageWithExcerpt	LCE:Master Excerpt List

Step-by-step guide

Multiexcerpt include

SpaceWithExcerpt	com.atlassian.confluence.content.render.xhtml.model.resource.identifiers.SpaceResourceIdentifier@7627108f
MultiExcerptName	Warning
PageWithExcerpt	_General

Step 1 - Drilling Preparation

Select the part of the machine where the high-front or top-mount bracket will be installed. Ensure this location, whether on the chassis or a panel, is away from any existing components or exposed wiring.
1. Mark where you may want to mount the reader with a permanent marker if needed.

Image Removed

Whether keeping the chassis/panel intact, exposing, or removing saidchassis/panel, apply some cutting oil where drilling through metal will takeplace.
Drill the oiled section in question carefully using the tungsten carbidetipped hole cutter.
Image Modified
Image Modified
Image Modified
With the drilled hole prepped, you are nowready to mount the reader.

Image Removed

Image Added

Step 2 - Mounting the bracket & reader

Tip
Please choose the tab that is associated with the type ofinstallation you are completing.

High-front mount

In a high-front mounting solution where the FasCard readerwill be angled downward toward the customer in regard to tallermachines, our C-6465 bracket would be used for thisinstall.

Image Added

Expand

Image Removed

title	High-front mount Step-by-step guide

Attach the C-6465 High Mount Bracket in itsplace, securing it down with a chase nipple.
Image Modified
Mount the universal bracket to the high-frontbracket with two (2) 8-32 screws and feed theharness wiring through the center. Whether choosing to feedwiring first or mounting the bracket first is no problem as longas the end result (pictured below) is achieved.

Image Removed

Image AddedImage Added
Connect the harnesses to their appropriate locations in the backof the reader.
1. For information about where the individual harnessesconnect to, please see F2: FasCard Touchscreen Reader.

Image Removed

1. Image Added
Slowly mount the reader to the corresponding bracket with thetop lip catching the locking edge and carefully wedging thereader in place. Ensure no metal edges of the bracket arevisible.

Image Removed

Image Added

Secure the reader with the provided T15 secure torxscrews on the bottom.

This may be part of the install kits or the screwsused from a previous high-front solution.

Image Modified

Note

title	Screwdriver Angling

As the reader is angled downward inhigh-front solutions, securing the reader may require a thinner secure torx screwdriver or a flex extension for the appropriate torx bit to accommodate for the angle.

Only F3 FasCard readers – Remove any plastic protectors (if still present) from thetouchscreen or EMV chip insert label.

Top-

mount

Mount

Warning

title

Swipe Clearance Notice

As stated above, only for top-mount solutions thefront of the top-mount bracket 1-1/4 inches from

thefront

the front of the machine, to allow for card swipe clearance.

Ensure the drilled hole aligns accordingly. Mounting thetop-mount bracket any further back then 1-1/4inches from the front of the machine tothe edge of the reader can potentially interfere withmounting the reader to the bracket and may prevent usersfrom being able to swipe or insert a card into the readerdue to lack of clearance.

In a top-mount solution, the process differs slightly from afront or high-front mounting solution. Our C-6452bracket would be used in this orientation.

Image Added

Expand

Image Removed

title	Top-mount Step-by-step guide

Attach the top-mount bracket onto the top panel of themachine, securing down with the chase nipple.Ensure the appropriate wiring is fed through the center holefor connecting to the reader.

Image Removed

Image Added
Connect all harnesses to the rear of the touchscreen readerwhere required.
1. For information about where the individual harnessesconnect to, please see F2: FasCard Touchscreen Reader.

Image Removed

1. Image Added
Slowly mount the reader to the corresponding bracket with thetop lip catching the locking edges (shown in red) and carefullywedge the reader in place.
Aligning the reader to the top mount also secures the groundpost (show in teal) to the reader.