Versions Compared

Version Old Version 18 New Version 19
Changes made by

Chris Kite

Christopher Patac

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.


Panel
borderColor#416EB6
titleColor#ffffff
titleBGColor#416EB6
titleOverview

This install guide goes over the detailed installation steps for an F2/F3touchscreen FasCard/FLEX reader onto an existing machine in either ahigha high-front or top-mount position.

Note

C-5402/C-5426-BASE incompatibility

The below solutions are not compatible with previousused previously used high-front/top mount readers or mounting bases.

Warning

Swipe Clearance Notice

For top-mount placements, CCI strongly recommends mounting the front of the top-mount bracket 1-1/4 inches from the front of the machine, to allow for card swipe clearance.

Ensure the drilled hole aligns accordingly. Mounting the top-mount bracket any further back then 1-1/4inches from the front of the machine to the edge of the reader can potentially interfere with mounting the reader to the bracket and may prevent users from being able to swipe or insert a card into the reader due to lack of clearance.

Required parts & tools

Readers

Bw part list
PartsC-5401,C-5403,C-5520
ShowDesc2true
ShowImagetrue
ShowDesc1true

Kits

Expand
titleTop High-Front Mount Kit
Cci kits
KitIDI-X0020X0021
ShowKitIDtrue
ShowKitDesctrue
Expand
titleHigh-Front Top Mount Kit
Cci kits
KitIDI-X0021X0020
ShowKitIDtrue
ShowKitDesctrue

Recommended tools & supplies (not included)

PageWithExcerpt
Expand
titleItems not included
multiexcerpt
Excerpt-include
MultiExcerptNameF2 Tools
LCE:Master Excerpt List
LCE:Master Excerpt List
nameFasCard reader tools and supplies
nopaneltrue


Step-by-step guide

Insert excerpt
LCE:Master Excerpt List
LCE:Master Excerpt List
nameWarning
nopaneltrue

Multiexcerpt include
macro_uuid11bdf2e8-444e-40ae-8d37-c63eda678589
SpaceWithExcerptcom.atlassian.confluence.content.render.xhtml.model.resource.identifiers.SpaceResourceIdentifier@7627108f
MultiExcerptNameWarning
PageWithExcerpt_General

Step 1 - Drilling Preparation

  1. Select the part of the machine where the high-front or top-mount bracket will be installed. Ensure this location, whether on the chassis or a panel, is away from any existing components or exposed wiring.

    1. Mark where you may want to mount the reader with a permanent marker if needed.

  2. Whether keeping the chassis/panel intact, exposing, or removing saidchassissaid chassis/panel, apply some cutting oil where drilling through metal will takeplacetake place.

  3. Drill the oiled section in question carefully using the tungsten carbidetipped carbide tipped hole cutter.


  4. With the drilled hole prepped, you are nowready now ready to mount the reader.

Step 2 - Mounting the bracket & reader

Tip

Please choose the tab that is associated with the type ofinstallation of installation you are completing. 

High-front mount

In a high-front mounting solution where the FasCard readerwill reader will be angled downward toward the customer in regard to tallermachinestaller machines, our C-6465 bracket would be used for thisinstallthis install.

Expand
titleHigh-front mount Step-by-step guide

  1. Attach the C-6465 High Mount Bracket in itsplaceits place, securing it down with a chase nipple.Image Removed

    Image Added

  2. Mount the universal bracket to the high-frontbracketfront bracket with two (2) 8-32 screws and feed theharness the harness wiring through the center. Whether choosing to feedwiring feed wiring first or mounting the bracket first is no problem as longas the end result (pictured below) is achieved.

  3. Connect the harnesses to their appropriate locations in the backof back of the reader.

    1. For information about where the individual harnessesconnect harnesses connect to, please see F2: FasCard Touchscreen Reader. 

  4. Slowly mount the reader to the corresponding bracket with thetop the top lip catching the locking edge and carefully wedging thereader the reader in place. Ensure no metal edges of the bracket arevisibleare visible.

  5. Secure the reader with the provided T15 secure torxscrewstorx screws on the bottom.

    1. This may be part of the install kits or the screwsused screws used from a previous high-front solution.Image Removed

      Image Added
      Note
      titleScrewdriver Angling

      As the reader is angled downward inhigh-front solutions, securing the reader may require a thinner secure torx screwdriver or a flex extension for the appropriate torx bit to accommodate for the angle.

  6. Only F3 FasCard readers – Remove any plastic protectors (if still present) from thetouchscreen the touchscreen or EMV chip insert label.

Top-Mount

Warning

Swipe Clearance Notice

As stated above, only for top-mount solutions thefront the front of the top-mount bracket 1-1/4 inches from the front of the machine, to allow for card swipe clearance.

Ensure the drilled hole aligns accordingly. Mounting thetopthe top-mount bracket any further back then 1-1/4inches from the front of the machine tothe to the edge of the reader can potentially interfere withmounting with mounting the reader to the bracket and may prevent usersfrom users from being able to swipe or insert a card into the readerdue reader due to lack of clearance.

In a top-mount solution, the process differs slightly from afront or high-front mounting solution. Our C-6452bracket would be used in this orientation.

Expand
titleTop-mount Step-by-step guide

  1. Attach the top-mount bracket onto the top panel of themachinethe machine, securing down with the chase nipple. Ensure the appropriate wiring is fed through the center holefor hole for connecting to the reader.

  3. Connect all harnesses to the rear of the touchscreen readerwhere reader where required.

    1. For information about where the individual harnessesconnect harnesses connect to, please see F2: FasCard Touchscreen Reader.

  4. Slowly mount the reader to the corresponding bracket with thetop the top lip catching the locking edges (shown in red) and carefullywedge carefully wedge the reader in place.

  5. Aligning the reader to the top mount also secures the groundpost ground post (show in teal) to the reader.

  6. Secure reader with the included T15 Secure Torx screws on the bottom.

  7. Only F3 FasCard readers – Remove any plastic protectors (if still present) from the touchscreen or EMV chip insert label.

Related documentation

Filter by label (Content by label)
showLabelsfalse
showSpacefalse
sortmodified
reversetrue
excludeCurrenttrue
cqllabel in ( "f3reader" ,"f2reader" ) and space = "LCE" and type ="page"