Page Comparison

Step-by-step guide

Step 1 – Unmounting the

Touchscreen

monitor

1. Disconnect any connected cables (power, video, touchscreen input (USB))

before proceeding

1. from the monitor.

Image Removed

Unmount the existing monitor from the bracket.

Unmount existing monitor from cabinet.

For v1 cabinets, three (3) bracket

1. Set the cables inside the cabinet so they can be used later.
   Image Added

2. To begin unmounting the monitor, verify what cabinet version you are working with.

   1. In V1 cabinets remove the three kep nuts to the left and right of the touchscreen

should be unfastened to

1. 1. . Unfasten the kep nuts fully then pull the

mounting

1. 1. monitor assembly back toward you to remove

touchscreen. DO NOT

1. 1. it.

      1. Do not remove the four

(4)

1. 1. 1. -center VESA screws

in this step if replacing a monitor in a v1 cabinet!This would also require unmounting the card dispenser tray, as the brackets share two of the same mounted bolt threads

1. 1. 1. .

   2. For

v2

1. 1. V2 cabinets

, only

1. 1. remove the four

(4) VESA screws (Green) should be unfastened to unmount the touchscreen from its mounted bracket from the front of the X-Changer door

1. 1. center VESA screws and push the monitor outward.

      1. Do not remove the kep nights to the left and right of the mounting bracket.

v1 Cabinet (Elo)	v2 Cabinet (Elo / Zuljana)
	Image Removed

Mounting a New or Replacement Touchscreen

Prior to

Image Added

Step 2 – Installing the replacement touchscreen

Before mounting a touchscreen to a specific cabinet type, the touchscreen will need to be mounted attached to its respective bezel.

Expand
title Version 1 Cabinet
Warning IMPORTANT V1 Cabinets are not compatible with the Zuljana touchscreen. DO NOT USE A ZULJANA TOUCHSCREEN WITH V1 CABINETS. It is strongly recommended to use properly listed ELO touchscreens. Failure to do so may result in a non-working touchscreen and will not be supported by CCI. Requirements Image Removed Install Components K-1500-TS: Elo Touchscreen Kit Installation components Cci kits Type Parts KitID K-1500-TS ShowKitID true ShowKitDesc true Tips Tip Upon removing the existing monitor, attach the monitor edge gasket (C-1380) to the cabinet prior to before installing the new monitor. Instructions Elo Touchscreen Place Step-by-step guide: Place the new touchscreen monitor face down on monitor bezel. If the new monitor uses the same bezel as the old monitor, you can remove the old touchscreen from its bezel to reuse the bezel component. Elo touchscreens use bezel C-1053B. Image Removed Image Added Attach the bezel mounting screws to the touchscreen. Ensure the bezel remains as flush as possible with the touchscreen without recessing back. Eight (8) screws will fasten into all eight (8) holes along the top, bottom, and sides of the monitor. In some v1 cabinet instances, only the top and bottom four (4) holes would need to be fastened with bezel mounting screws. Place bracket (C-1056) across the back of the touchscreen monitor and attach supplied VESA mounting screws (equivalent to C-1011) to the monitor. Image RemovedImage Added Attach the monitor edging (C-1380) to cabinet prior to installation of the cabinet before installing the new monitor. Attach the bracket-mounted unit to the bolts on the front door of the cabinet from behind the door and tighten down using existing the previously removed kep nuts. Re-attach the cables to the newly installed monitor. Image RemovedImage Added Connect and hand-tighten screws from the blue VGA video cable. Connect the USB cable. Attach Connect the barrel-shaped power supply cable. Reboot Restart the computer.

Install Components

Installation components

Expand
title Version 2 Cabinet
Warning Zuljana Touchscreens and Older LaundryCard Zuljana touchscreens are only compatible with version 9 software. DO NOT USE ZULJANA TOUCHSCREENS WITH V8 OR OLDER SOFTWARE. Must either upgrade to LaundryCard v9 or utilize an Elo touchscreen. Requirements Image Removed
Version 2 Cabinet

Elo Touchscreen for older Elo touchscreens w/ integrated bezel (K-1504-TSA)	Zuljana Touchscreen for older Elo touchscreens w/ integrated bezel (K-1504-TSB)	Zuljana Touchscreen for existing flat Elo touchscreens (K-1504-TSC)
Cci kits Type Parts KitID K-1504-TSA	Cci kits Type Parts KitID K-1504-TSB	Cci kits Type Parts KitID K-1504-TSC

Step 1-by-step guide:

ELO Touchscreen	Zuljana Touchscreen
Image RemovedImage Added	Image RemovedImage Added

1. Place the new touchscreen monitor face down on the monitor bezel. If the new monitor uses the same bezel as the old monitor, you can remove the old touchscreen from its bezel to reuse the bezel component.

   1. ELO touchscreens use bezel C-1053B.

   2. Zuljana touchscreens use bezel C-1053B-V2.

Step 2

ELO Touchscreen	Zuljana Touchscreen
Image RemovedImage Added	Image RemovedImage Added

1. Attach the bezel mounting screws to the touchscreen. Ensure the bezel remains as flush as possible with the touchscreen without recessing back.

   1. Eight (8) screws will fasten into all eight (8) holes along the top, bottom, and sides of the monitor.

Step 3

Image Removed

1. Place the touchscreen with bezel attached back into the X-Changer door from the front. 

Step 4

Image Removed

1. Image Added

2. Secure the touchscreen to monitor using the provided VESA 75 screws while ensuring the display is high enough on the bracket to have the monitor buttons visible.

   Image Added

Step 5

Image Removed

1. Re-attach cables to the newly installed monitor.

   1. Connect and hand-tighten screws from the blue VGA video cable.

   2. Connect the USB cable.

1. 1. Connect the barrel-shaped power supply cable.

1. 1. Image Added

2. Reboot the computer.

Configure and Calibrate the Touch Screen

The Configure Hardware Tool

Image Removed

Step 3 – Configuring and calibrating the touchscreen

The latest Configure Hardware tool within LaundryCard v9.1.9 or newer is able to can recognize whether the installed touchscreen is an Elo or Zuljana touchscreen and apply the appropriate settings.

Image Added

1. After the hardware installinstallation, open Windows Explorer by either pressing the Windows Key and clicking the Windows Explorer colored manila folder or use using the Windows shortcut WIN+E.

2. Navigate to D:\Setup\InstallProcs.

3. Run the configurehardware.cmd script.

4. Select option G to configure just the touchscreen.

The appropriate drivers and settings (including the Calibration Tool for Elo touchscreens) will then installbe installed.

When an Elo touchscreen is installed, direct interaction with the touchscreen may be required if the display is not already calibrated.

With Zuljana touchscreens, Configure Hardware will restart the system after a new monitor install is installed before reaching the diagnostic screen for post-config testing , if a Zuljana touchscreen has never been used on the X-Changer in question.

Manual Calibration (Elo Only)

Upon rebooting the computer:

1. When KeepAGoin is visible and the startup countdown displays, select the Pause button on the screen.

   • May take a couple of tries if the monitor is poorly uncalibrated.

2. Press the Windows key on the keyboard to bring up the taskbar.

3. Begin typing the application name 'Control Panel' until the search populates the Control Panel.

4. Select the control panel settings option 'Elo Touchscreen'.

   • (If you do not see the settings option then the Elo software will need to be installed.)

5. Under the "Properties 1" tab, click the Align button and follow the prompts to align the touchscreen.

6. Close the Elo Touchscreen Control Panel window and bring back up the KeepAGoin window.

7. Click the Refresh button to restart the startup countdown.