Versions Compared

Old Version 1

changes.mady.by.user Chris Kite

Saved on

compared with

New Version Current

changes.mady.by.user Chris Kite

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Cci readerinstall header

Install Mounting Hardware

Cci readerinstall kit
KitID584
KitDescCoin and Card

  1. Place the C-6700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to for further instructions.

Cci readerinstall kit
KitID863
KitDescCard Only - Coin Ready Models

  1. Remove existing coin box.

  2. Remove Vault Switchand bridge the wires previously connected to the Vault Switchwith the C-5365 Bypass Harness.

  3. Bend the side tabs of theC-6602Vault Bracketoutward and install into the coin vault. The tabs should snap into place securing the bracket.

  4. Before securing the reader to the machine with C-0144 Screws, place the C-0906 Spacerbetween the reader and machine so the Screwspass through the circular holes in theSpacer.
Cci readerinstall kit
KitID865
KitDescCard Only - Card Ready Models
  1. Install the C-6970Alliance Mounting Bracketinto the opening on the control panel for mounting card readers and coin drops.
  2. Attach the C-5414F2 Mounting Bracketto the C-6970Alliance Mounting Bracketand secure using the C-1060Screws.
  3. Refer to for further instructions.

Connect Power

Cci readerinstall kit
KitID581

  1. Connect the C-6204-40 Power Adapter Harness (12VDC power) to the H10 connection on the Machine Control Assembly.

    1. Secure the green wire beneath the ground screw.

Connect Coin Sense Harness

Cci readerinstall kit
KitID700
KitDescCoin Drop: Factory
  1. Disconnect the coin drop from the machine control assembly.
  2. Connect the C-6250 Coin Sense Harness to the harness connected to the coin drop.

Connect Machine Interface Harness

Cci readerinstall kit
KitID582
KitDescPulse and Serial
  1. Connect the C-5240 Machine Start Harness to the H3 connector on the Machine Control Assembly.

Connect and Mount Reader

Multiexcerpt include
SpaceWithExcerptCCIDOC
MultiExcerptNameF2 Reader
PageWithExcerpt_Reader Ports

Item No.ComponentNotes
1Power Connection PortUtilizes the same power harnesses as the first generation FasCard reader.
2Pulse Connection PortConnection point for pulse machine start harnesses.
3Coin 1 Connection PortThis is the connection point for the harness input associated with Coin 1.
4Coin 2 Connection PortThis is the connection point for the harness input associated with Coin 2.
5Serial Connection PortThis is the connection point for serial machine start harnesses.
  1. Feed remaining harness ends through mounting hole as described inF2/F3 FasCard Reader Mounting Guide.
  2. Connect the free end of theC-5240 Machine Start Harnessto port 5 (Serial Connection Port) as shown in the image above.
  3. Connect the free end of the C-6250 Coin Sense Harness to port 3 (Coin 1 Sense Harness Connection Port) as shown in the image above.
  4. Connect the free end of the C-6204-40 Power Extension Harness to port 1 (Power Harness Connection Port) as shown in the image above.
  5. Connect FasCard reader to base as described in theF2/F3 FasCard Reader Mounting Guide.

Machine Configuration

ACA machines using a serial configuration require dip switch 3 on theMachine Control Boardto be set to the 'ON' position.Leave all other dip switches as is.

Cci readerinstall footer