Versions Compared

Old Version 1

changes.mady.by.user Brett Norrell

Saved on

compared with

New Version Current

changes.mady.by.user Chris Kite

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Cci readerinstall header

Install Mounting Hardware

Cci readerinstall kit
KitID917
KitDescCoin and Card

  1. Place the C-5700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to FasCard Mounting Guide for further instructions.

Cci readerinstall kit
KitID1046
KitDescCard Only - Rear Control Coin Slide Models

  1. Remove existing coin box and coin slide.

  2. Install C-5762 Metercase Bracket over the front of the metercase and secure using the C-0301 Mounting Bolt.

Cci readerinstall kit
KitID792
KitDescCard Only - Rear Control Coin Drop Models

  1. Remove existing coin box and coin drop.

  2. Remove connections to coin vault service switch and bridge connections using C-5365 Bypass Harness.

  3. Install C-5762 Metercase Bracket over the front of the metercase and secure using the C-1059 Kep Nut, and C-1070-W Washer.

Cci readerinstall kit
KitID791
KitDescCard Only - 10 Degree Front Panel Coin Drop Models

  1. Remove existing coin box and coin drop.

  2. Remove connections to coin vault service switch and bridge connections using C-5365 Bypass Harness.

  3. Install C-5765-W Metercase Bracket over the front of the metercase and secure using the C-1059 Kep Nut, and C-1070-W Washer.

Cci readerinstall kit
KitID905
KitDescCard Only - Card Ready Models

  1. Place the C-5700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to FasCard Mounting Guide for further instructions.

Connect Power

Cci readerinstall kit
KitID595
KitDescNon-ACA Control Equipped Models

  1. Tap power as described in the Fascard Reader Install - Universal Concepts document using the C-5101 Spade Taps provided.

  2. Connect the C-5210 Power Adapter Harness to the installed spade taps. Connect the opposite end to the C-5602 Power Converter.

  3. Connect the C-5500 Power Extension Harness to the appropriate connector on the C-5602 Power Converter. The remaining cable end connects to the FasCard reader.

Cci readerinstall kit
KitID581
KitDescACA Control Equipped Models

  1. Connect the C-6204-40 12VDC Power Harness to the H10 connection on the machine control assembly.

    1. Secure the green wire beneath the ground screw.

  2. Connect the opposite end of the C-6204-40 Power Adapter Harness (3-pin molex) to the F2 reader.

Connect Coin Sense Harness

Cci readerinstall kit
KitID674
KitDescCoin Drop: ACA Control Models

  1. Disconnect the Coin Drop from the Machine Control Assembly.

  2. Connect the C-5250 Coin Sense Harness to the harness connected to the Coin Drop.

Cci readerinstall kit
KitID677
KitDescCoin Drop: Coin Slide Models

  1. Disconnect the Coin Drop from the Machine Control Assembly.

  2. Connect the C-5253 Coin Sense Harness to the micro switch on the coin slide.

Connect Machine Interface Harness

Cci readerinstall kit
KitID645
KitDescPulse - Optical Coin Drop

  1. Connect the C-5300-NC Machine Start Harness to the Coin 1 connection on the Machine Control Assembly.

Cci readerinstall kit
KitDescPulse - Coin Slide
isMissingRequiredParameterstrue

  1. Connect the C-5256 Machine Start Harness to the hard previously connected to the coin slide micro switch.

Cci readerinstall kit
KitID582
KitDescPulse - Serial Connection

  1. Connect the C-5240 Machine Start Harness to the H3 connection on the Machine Control Assembly.

Connect and Mount Reader

Multiexcerpt include
SpaceWithExcerptCCIDOC
MultiExcerptNameF1 Reader
PageWithExcerpt_Reader Ports

  1. Feed remaining harness ends through the mounting hole as described in F1: FasCard Reader Mounting Guide.

  2. Connect the free end of the Machine Start Harness to the appropriate port.

    1. For pulse start harnesses (white connector), connect to port 2 (Pulse Connection Port) as shown in the image above.

    2. For serial start harnesses (black connector), connect to port 1 (Serial Connection Port) as shown in the image above

  3. Connect the free end of the Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.

  4. Connect the free end of the C-5500 Power Extension Harness to port 4 (Power Harness Connection Port) as shown in the image above.

  5. Secure the FasCard reader to base as described in the F1: FasCard Reader Mounting Guide.

Machine Configuration

ACA machines using a serial configuration require dip switch 3 on the Machine Control Board to be set to the 'ON' position. Leave all other dip switches as is.

Cci readerinstall footer