Versions Compared

Old Version 3

changes.mady.by.user CCI Integration User

Saved on

compared with

New Version Current

changes.mady.by.user CCI Integration User

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Cci readerinstall header

Install Mounting Hardware

  • Place the C-6700-TEMP Drill Template on the desired mounting location.

  • Verify included harnesses will reach desired location without encountering interference from internal machine components.

    • Refer to for further instructions.
    cci-readerinstall-kitstep
    KitID841
    KitDescCoin and Card
    componentMounting

  • Remove existing coin box.

  • Bend the side tabs of the C-0941 Vault Cover outward and install into the coin vault. The tabs should snap into place securing the bracket.

  • Place the C-6700-TEMP Drill Template on the desired mounting location.

  • Verify included harnesses will reach desired location without encountering interference from internal machine components.

    • Refer to for further instructions.
    cci-readerinstall-kit
    KitID854
    KitDescCard Only

    ...

    step
    componentPower

    Tap power as described in the document by connecting the C-5101 Power Adapter Harness to the power distribution panel inside the machine.

    1. 120vac: Connect the brown and blue wires to connector #2 closest to outside of machine and #4 on terminal side closest to circuit board.

    2. 240vac: Connect the brown and blue wires to connectors 3 and 5 on the terminal side closest to the circuit board.

    3. Secure the green wire beneath the ground screw.

  • Connect the opposite end of the C-5101 Power Adapter Harness to the C-5602 Power Converter.

  • Connect the C-5500-84 Power Extension Harness to the appropriate connector on the C-5602 Power Converter. The remaining cable end connects to the FasCard reader.

    • cci-readerinstall-kit
    KitID0
    KitDescChange Me

    ...

    step
    componentPower

  • Disconnect the Coin Drop from the Machine Control Assembly.
    • Connect the C-6357 Coin Sense Harness to the harness connected to the Coin Drop.
    cci-readerinstall-kit
    KitID716
    KitDescCoin Drop: Factory Edge Connector
    step
    componentCoin Sense

    cci-readerinstall-kitstep
    KitID718
    KitDescCoin Drop: Factory Terminal Connector
    1. Disconnect the Coin Drop from the Machine Control Assembly.
    2. Connect the C-6358 Coin Sense Harness to the harness connected to the Coin Drop.
      1. Connect the coin drop wires to the matching colored wires on the coin sense harness.

    Connect Machine Interface Harness

    Connect the C-5353R1 Machine Start Harness to the Coin 1 connector on the Machine Control Assembly.
    Cci readerinstall kit
    KitID655
    KitDescPulse - Edge Connector
    componentStart

    Cci readerinstall kit
    KitID659605
    KitDescPulse - Terminal Connector

    1. Connect the

    C-5356 Machine Start Harness to the Positions 2 and 3 on the terminal block.
    Cci readerinstall kit
    KitID830
    KitDescPulse - Terminal Connector with Block
  • Attach the C-5313 Terminal Block to the Machine Control Assembly.
    • Connect the C-5356

    1. bare wire ends of the C-0111-RES Machine Start Harness to

    the Positions 2 and 3 on

    1. the terminal block.

    2. Terminal block

    positions

    1. connections are numbered 0-6

    . Position 0 is closest to the board edge.

    Connect and Mount Reader

    Multiexcerpt include
    SpaceWithExcerptCCIDOC
    MultiExcerptNameF2 Reader
    PageWithExcerpt_Reader Ports

    ...

    1. Feed remaining harness ends through the mounting hole as described in the F2/F3: FasCard Reader Mounting Guide.
    2. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.
    3. Connect the free end of theCoin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.
    4. Connect the free end of the C-5500-84 Power Harness to port 1.
    5. Secure the FasCard reader to base as described in the FasCard Mounting Guide.

    Machine Configuration

    ...

    1. from the edge nearest the top of the board (position 0) to the bottom of the terminal block (position 6)

      • For machines shipped before 1/1/2006, connect harness to positions 1 and 3.

      • For machines shipped after 1/1/2006, connect harness to positions 3 and 5.

      • For machines shipped near 6/1/2007, connect harness to positions 2 and 3.

      • All other machines, connect harness to positions 3 and 4.

    Cci readerinstall step
    componentReader

    Cci readerinstall footer