3631 Reader Install Guide

Install Mounting Hardware

 I-M0104

Part #: C-5710

Desc 1: Rubber Grommet

Desc 2: 3/4"

   Qty: 1

Part #: C-6801

Desc 1: F2/F3 Reader Mounting Kit

Desc 2: Universal

   Qty: 1

1. Place the C-6700-TEMP Drill Template on the desired mounting location.

2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

3. Refer to FasCard Mounting Guide for further instructions.

 I-M0181

Part #: C-6976

Desc 1: F2 Quantum Touch Stk Dryer

Desc 2: Mount

   Qty: 1

Part #: C-1073

Desc 1: Nut

Desc 2: 10-24 - Kep

   Qty: 4

Part #: C-5365

Desc 1: Bypass Harness

Desc 2: Alliance Coin Vault Bypass

   Qty: 1

Part #: C-5420

Desc 1: Screw

Desc 2: 10-32 x ¼" - Pan

   Qty: 2

Part #: C-5416

Desc 1: Screw

Desc 2: 8-32" x 3/8" - Button - Torx

   Qty: 2

Part #: C-5414

Desc 1: F2/F3 Std. Mounting Bracket

Desc 2: Sheet metal base

   Qty: 1

1. (Coin Model Only) Install the C-5365 Bypass Harness by removing the coin vault switch and connecting the spade terminal connections to C-5365 Bypass Harness.

2. Remove factory payment device bay cover or card reader mounting plate.

3. Place the C-6976 Quantum Touch Stk Dryer Mounting Bracket into the payment device opening and secure using the (4) C-107310-24 Hex Nut.

4. Align the C-5414 F2 Mounting Bracket with the C-6976 Quantum Touch Stk Dryer Mounting Bracket and attach using the (2) C-5420 10-32 x 1/4" Screws.

Connect Power

 I-P0002

Part #: C-6204-40

Desc 1: Power Adapter Harness

Desc 2: F2, 12vDC Pow Harness - 40"

   Qty: 1

1. Connect the C-6204-4012VDC Power Harness to the H10 connection on the Machine Control Assembly.
   1. Connect the green wire to a chassis ground.
2. The remaining end (3-pin molex) connects directly to the rear of the F2 FasCard Reader.

Connect Coin Sense Harness

 I-S0027

Part #: C-6250

Desc 1: Coin Sense Harness

Desc 2: F2

   Qty: 1

1. Disconnect the Coin Drop from the Machine Control Assembly.
2. Connect the C-6250 Coin Sense Harness to the harness connected to the Coin Drop.

Connect Machine Interface Harness

 I-T0003

Part #: C-5240

Desc 1: Machine Start Harness

Desc 2: Alliance ACA

   Qty: 1

1. Connect the C-5240 Machine Start Harness to the H3 connector on the Machine Control Assembly.

Connect and Mount Reader

1. Feed remaining harness ends through the mounting hole.
2. Connect the free end of the C-5240 Machine Start Harness to port 5 (Serial Connection Port) as shown in the image above.
3. (Coin and Card Installation Only) Connect the free end of the C-6250 Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.
4. Connect the free end of the C-6204-40 Power Extension Harness to port 1 (Power Harness Connection Port) as shown in the image above.

Machine Configuration

Alliance Touch Controls

1. Enter the service menu by touch and holding on the top-center of the touch screen for 3 seconds.

   1. Enter password if required.

2. Configure the machine with the following settings:

   1. Payment Settings:

      • Card Reader: Enabled

      • Serial Payment System: Enabled