Skip to end of banner
Go to start of banner

0404 Reader Install Guide

Skip to end of metadata
Go to start of metadata

You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 6 Next »

Warning!

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses.

It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Overview

Equipment Details

Type: Washer
Manufacturer: Laundrylux
Make: Wascomat
Model Length: 4

Non-Compass/Compass Pro Control

For Set-O-Matic drop, set Dip Switch 7 to ON (?)

Associated Models


W620
W630
W640
W645
W650
W655
W675

Recommended Tools and Supplies

  • Drill

  • 1 1/8" Tungsten Carbide Tipped Hole Cutter

  • Cutting Oil

  • 9/64" Drill Bit

  • Center Punch

  • Hammer

  • Fine Point Permanent Marker

  • Pliers

  • Tape Measure

Installation

Install Mounting Hardware

 I-M0131

Part #: C-1059

Desc 1: Nut

Desc 2: 10-32 - Kep

   Qty: 2

Part #: C-6920R1

Desc 1: Mounting Bracket

Desc 2: 6" Straight w/ studs

   Qty: 1

Part #: C-5420

Desc 1: Screw

Desc 2: 10-32 x ¼" - Pan

   Qty: 2

Part #: C-5416

Desc 1: Screw

Desc 2: 8-32" x 3/8" - Button - Torx

   Qty: 2

Part #: C-5414

Desc 1: F2/F3 Std. Mounting Bracket

Desc 2: Sheet metal base

   Qty: 1

  1. Remove existing coin box and coin drop.

  2. Attach the C-5414 Bracket on to the C-6920R1 Vault Bracket using C-5420 Screws.

  3. Install the C-6920R1 Vault Bracket in to the coin vault and drop opening. Secure into place using C-1059 Kep Nut.

Connect Power

Connect Coin Sense Harness

 I-S0052

Part #: C-6389

Desc 1: Coin Sense Harness

Desc 2: Set-O-Matic

   Qty: 1

  1. Disconnect the Coin Drop from the Machine Control Assembly.

  2. Connect the C-6389 Coin Sense Harness to the harness connected to the Coin Drop.

Connect Machine Interface Harness

 I-T0027

Part #: C-0119R1F

Desc 1: Machine Start Harness

Desc 2: Pins 1&4 on End B - Rotary

   Qty: 1

  1. Connect the C-0119R1F Machine Start Harness to the 6-pin start harness coming from the Machine Control Assembly.

Connect and Mount Reader

CCI Software Configuration

Machine ControlPulseSerial
Compass (Gen6)SingleVend (Relay) / 42msLaundrylux Compass Washer
Compass Pro (Gen7)SingleVend (Relay) / 42msmsLaundrylux Compass Pro Washer
Keltner - PulseSingleVend (Relay) / 1000ms*NOT SUPPORTED*
Rotary Timer - PulseSingleVend (Relay) / 2000ms*NOT SUPPORTED*
Set-O-Matic - PulseSingleVend (Relay) / 100ms*NOT SUPPORTED*

Additional Resources

  • No labels