Skip to end of banner
Go to start of banner

3698 Reader Install Guide

Skip to end of metadata
Go to start of metadata

You are viewing an old version of this page. View the current version.

Compare with Current View Page History

Version 1 Current »

Warning!

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses.

It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Overview

Equipment Details

Type: Tumble Dryer (Stack)
Manufacturer: ONNERA Group
Make: [VARIES]
Model Length: Not Set

Associated Models

UDTT235G
UDTT250G
UDTT280G

Recommended Tools and Supplies

  • Drill

  • 1 1/8" Tungsten Carbide Tipped Hole Cutter

  • Cutting Oil

  • 9/64" Drill Bit

  • Center Punch

  • Hammer

  • Fine Point Permanent Marker

  • Pliers

  • Tape Measure

Installation

Install Mounting Hardware

 I-M0003

Part #: C-6801

Desc 1: F2/F3 Reader Mounting Kit

Desc 2: Universal

   Qty: 1

  1. Place the C-6700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to F2/F3 Mounting Guide for further instructions.

 I-M0142

Part #: C-5800

Desc 1: F1 Reader Mounting Kit

Desc 2: Universal

   Qty: 1

  1. Place the C-5700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to F1 Reader Mounting Guide for further instructions.

 I-M0191

Part #: C-0971

Desc 1: LC Mounting Bracket

Desc 2: Fagor Machine

   Qty: 1

Part #: C-0141

Desc 1: Screw

Desc 2: 8-32 x 1-1/2" - Cap

   Qty: 2

Part #: C-0015

Desc 1: Label

Desc 2: Reader Cover Label

   Qty: 1

  1. Remove the existing payment device panel and put aside the fasteners securing the panel in place.

  2. Install the C-0971 LC Mounting Bracket into the payment device panel opening. Secure in place using the factory fasteners

 I-M0192

Part #: C-6971

Desc 1: FC Mounting Bracket

Desc 2: Fagor Machine

   Qty: 1

Part #: C-5801

Desc 1: F1 Reader Mounting Kit

Desc 2: Front

   Qty: 1

  1. Remove the existing payment device panel and put aside the fasteners securing the panel in place.

  2. Place the C-5700 Surface Mounting Bracket over the front of the C-6971 FC Mounting Bracket so the large, central, circular opening aligns with the C-5700 Surface Mounting Bracket.

  3. Insert the C-5702 Chase Nipple through the central circular opening and then secure in place on the other side of the panel with the C-5703 Nut.

  4. Install the C-6971 FC Mounting Bracket into the payment device panel opening. Secure in place using the factory fasteners.

 I-M0193

Part #: C-6971

Desc 1: FC Mounting Bracket

Desc 2: Fagor Machine

   Qty: 1

Part #: C-5420

Desc 1: Screw

Desc 2: 10-32 x ¼" - Pan

   Qty: 2

Part #: C-5416

Desc 1: Screw

Desc 2: 8-32" x 3/8" - Button - Torx

   Qty: 2

Part #: C-5414

Desc 1: F2/F3 Std. Mounting Bracket

Desc 2: Sheet metal base

   Qty: 1

  1. Remove the existing payment device panel and put aside the fasteners securing the panel in place.

  2. Place the C-5414 Standard Mounting Bracket over the front of the C-6971 FC Mounting Bracket so the three large, circular openings align and attach using the (2) C-5420 10-32 x 1/4" Screws.

  3. Install the C-6971 FC Mounting Bracket into the payment device panel opening. Secure in place using the factory fasteners.

 I-M0216

Part #: C-6802

Desc 1: FLEX RF Reader Mounting Kit

Desc 2:

   Qty: 1

  1. Place the C-6700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to F2/F3 Mounting Guide for further instructions.

 I-M0280

Part #: C-6971

Desc 1: FC Mounting Bracket

Desc 2: Fagor Machine

   Qty: 1

Part #: C-5420

Desc 1: Screw

Desc 2: 10-32 x ¼" - Pan

   Qty: 2

Part #: C-5416

Desc 1: Screw

Desc 2: 8-32" x 3/8" - Button - Torx

   Qty: 2

Part #: C-5403RF-BRACKET

Desc 1: Flex RF Reader

Desc 2: Mounting bracket

   Qty: 1

  1. Remove the existing payment device panel and put aside the fasteners securing the panel in place.

  2. Place the C-5403RF-BRACKET Mounting Bracket over the front of the C-6971 FC Mounting Bracket so the three large, circular openings align and attach using the (2) C-5420 10-32 x 1/4" Screws.

  3. Install the C-6971 FC Mounting Bracket into the payment device panel opening. Secure in place using the factory fasteners.

Connect Power

 I-P0008

Part #: C-5101

Desc 1: Spade Taps

Desc 2: 18-14 AWG

   Qty: 3

Part #: C-5210

Desc 1: Power Adapter Harness

Desc 2: CGI

   Qty: 1

Part #: C-5500-84

Desc 1: Power Extension Harness

Desc 2: 84"

   Qty: 1

Part #: C-5602R1

Desc 1: Power Converter

Desc 2: SMT-012-018VW

   Qty: 1

  1. Tap power as described in the Fascard Reader Install - Universal Concepts document using the C-5101 Spade Taps provided.

  2. Connect the C-5210 Power Adapter Harness to the installed spade taps. Connect the opposite end to the C-5602 Power Converter.

  3. Connect the C-5500-84 Power Extension Harness to the appropriate connector on the C-5602 Power Converter. The remaining cable end connects to the FasCard reader.

Connect Coin Sense Harness

 I-S0061

Part #: C-5372

Desc 1: F1 Coin Sense

Desc 2: Coin Sense Harness

   Qty: 1

  1. Disconnect the coin drop 6-pin connection from the machine.

  2. Connect the C-5372 Coin Sense Harness to the coin drop.

 I-S0062

Part #: C-6373

Desc 1: F2 Coin Sense

Desc 2: Coin Sense Harness

   Qty: 1

  1. Disconnect the coin drop 6-pin connection from the machine.

  2. Connect the C-6373 Coin Sense Harness to the coin drop.

Connect Machine Interface Harness

 I-T0095

Part #: C-5374R1

Desc 1: FC-LC Start Harness

Desc 2: Pulse Start Harness

   Qty: 1

  1. If coin drop is present, disconnect the coin drop from the extension harness for the CN8 connection and connect the C-5374R1 Pulse Start Harness to the 6-pin connector on the extension harness.

    domus-fagor_dryer_coin_connection.jpg

Extras

 I-X0042

Part #:

Desc 1: Kit ID: I-X0042

Desc 2:

   Qty: 0

Part #: C-5374R1-144

Desc 1: FC-LC Start Harness

Desc 2: Pulse Start Harness

   Qty: 1

Part #: C-6410

Desc 1: F3, SLV Stack Add On Dongle

Desc 2: Pulse / SingleVend

   Qty: 1

Part #: C-6971

Desc 1: FC Mounting Bracket

Desc 2: Fagor Machine

   Qty: 1

Part #: C-5033

Desc 1: Label

Desc 2: 4-5/8" x 3-1/2"

   Qty: 1

  1. If coin drop is present for the lower pocket, remove and disconnect it from the extension harness for the CN8 connection. Connect the C-5374R1-144 Pulse Start Harness to the 6-pin connector on the extension harness. Run the harness back to the upper pocket’s control housing to the card reader.

    domus-fagor_dryer_coin_connection.jpg

  2. Locate area to mount C-6410 Pulse Stack Add-On Board.

    1. Must be close enough to reader mounting location to connect the harness to.

    2. Must be on a surface that does not received direct exposure from any heating elements (If applicable.)

  3. Clean mounting location to remove any dust and residue if needed.

  4. Remove the sticker from the back of the C-6410 Pulse Stack Add-On Board to expose the adhesive and apply to the mounting location.

  5. Connect the white, 6-pin connector from the C-5374-144 Machine Start Harness to the J1 connection on the C-6410 Pulse Stack Add-On Board.

  6. Install the C-6971 Mounting Bracket into the lower pocket’s payment device opening. Secure in place using the factory hardware.

  7. Apply the C-5033 Label over the openings in the C-6971 Mounting Bracket.

 I-X0043

Part #:

Desc 1: Kit ID: I-X0043

Desc 2:

   Qty: 0

Part #: C-5374R1-144

Desc 1: FC-LC Start Harness

Desc 2: Pulse Start Harness

   Qty: 1

Part #: C-6410

Desc 1: F3, SLV Stack Add On Dongle

Desc 2: Pulse / SingleVend

   Qty: 1

Part #: C-6373-144

Desc 1: F2 Coin Sense

Desc 2: Coin Sense Harness

   Qty: 1

  1. Disconnect the coin drop from the lower pocket’s machine control assembly and connect to the C-6373-144 Coin Sense Harness.

  2. Connect the C-5374R1-144 Pulse Start Harness to the 6-pin connector on the CN8 extension harness for the lower pocket’s machine control assembly.

  3. Run both of the harnesses back to the card reader’s mounting location.

    domus-fagor_dryer_coin_connection.jpg

  4. Locate area to mount C-6410 Pulse Stack Add-On Board.

    1. Must be close enough to reader mounting location to connect the harness to.

    2. Must be on a surface that does not received direct exposure from any heating elements (If applicable.)

  5. Clean mounting location to remove any dust and residue if needed.

  6. Remove the sticker from the back of the C-6410 Pulse Stack Add-On Board to expose the adhesive and apply to the mounting location.

  7. Connect the white, 6-pin connector from the C-5374-144 Machine Start Harness to the J1 connection on the C-6410 Pulse Stack Add-On Board.

Connect and Mount Reader

 LaundryCard Reader (C-0100, C-0101, C-0102, C-0103)

  1. Feed remaining harness ends through mounting bracket.

  2. For serial setups:

    1. Connect the free end of the Machine Start Harness to port 1 (Serial Connection Port) as shown in the image above.

    2. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

  3. For coin pulse setups:

    1. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

  4. Connect the the Cat5 cables running to and from the adjacent machines to ports labeled 3 (Line Connection Ports) as shown in the image above.

  5. Secure the LaundryCard reader to the bracketry using included hardware.

 LaundryCard L2 Reader (C-0103-L2)

L2_Port_Guide.png

  1. Feed remaining harness ends through mounting bracket.

  2. For serial setups:

    1. Connect the free end of the Machine Start Harness to port 1 (Serial Connection Port) as shown in the image above.

    2. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

  3. For coin pulse setups:

    1. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

  4. Connect the free end of the Power Harness to port 1.

  5. Secure the L2 reader to base as described in FasCard F2/F3 Reader Installation Guide - Front Mount.

 F1 Reader (C-5001)

  1. Feed remaining harness ends through the mounting hole as described in the F1 Reader Mounting Guide.

  2. Connect the free end of the Machine Start Harness to port 1 (Serial Connection Port) as shown in the image above.

  3. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

  4. Connect the free end of the Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.

  5. Connect the free end of the Power Extension Harness to port 4 (Power Harness Connection Port) as shown in the image above.

  6. Secure the FasCard reader to base as described in the F1 Reader Mounting Guide.

 F2/FLEX Reader (C-5401, C-5402, C-5402E)

  1. Feed remaining harness ends through the mounting hole as described in FasCard F2/F3 Reader Installation Guide - Front Mount.

  2. For Serial Setups:

    1. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

    2. Connect the free end of the Machine Start Harness to port 5 (Serial Connection Port) as shown in the image above.

  3. For Pulse Setups:

    1. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

  4. Connect the free end of the Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.

    1. For dual coin drop setups connect the secondary Coin Sense Harness to port 4 (Coin Sense Harness Connection Port) as shown in the image above.

  5. Connect the free end of the Power Harness to port 1.

  6. Secure the FasCard reader to base as described in FasCard F2/F3 Reader Installation Guide - Front Mount.

 F3 Reader (C-5520, C-5520E)

TODO

  • No labels