3651 Reader Install Guide

Part #: C-5801

Desc 1: F1 Reader Mounting Kit

Desc 2: Front

   Qty: 1

1. Place the C-5700-TEMP Drill Template on the desired mounting location.

2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

3. Refer to the F1 FasCard Mounting Guide for further instructions.

Part #: C-5710

Desc 1: Rubber Grommet

Desc 2: 3/4"

   Qty: 1

Part #: C-6801

Desc 1: F2/F3 Reader Mounting Kit

Desc 2: Universal

   Qty: 1

1. Place the C-6700-TEMP Drill Template on the desired mounting location.

2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

3. Refer to F2 Reader Mounting Guide for further instructions.

Part #: C-6982

Desc 1: Maytag MLG22PD Bracket

Desc 2: F2

   Qty: 1

Part #: C-5414

Desc 1: F2/F3 Std. Mounting Bracket

Desc 2: Sheet metal base

   Qty: 1

Part #: C-5420

Desc 1: Screw

Desc 2: 10-32 x ¼" - Pan

   Qty: 2

Part #: C-5436

Desc 1: Screw

Desc 2: 10-32 x 1" - Pan MS

   Qty: 2

Part #:

Desc 1:

Desc 2:

   Qty: 1

Part #: C-5416

Desc 1: Screw

Desc 2: 8-32" x 3/8" - Button - Torx

   Qty: 2

1. Remove existing W11034287 Fascia from machine console panel. Remove the coin drop and coin box from the machine.

2. Insert C-6982 MayTag Adapter Bracket into the coin drop opening and align behind the coin drop bracket so the larger hole is towards the bottom. Then use (2) C-5420 10-32 x 1/4" Pan Screws to secure to the machine.
   

   

3. Install the W11034310 Fascia over the console panel.
   

   

4. Align the C-5414 F2 Standard Mounting Bracket with the holes in the C-6982 MayTag Adapter Bracket and attach together using (2) C-5436 10-32 x 1" Pan Screws.
   

   

Part #: C-5701

Desc 1: F1 Maytag Mounting Bracket

Desc 2: Small chassis stack dryers

   Qty: 1

Part #: C-1060

Desc 1: Screw - Build: TK

Desc 2: 8-32 x 3/8" - Zinc

   Qty: 4

Part #: C-5021

Desc 1: Label

Desc 2: Screw Cover

   Qty: 1

Part #: C-5027

Desc 1: Label

Desc 2: Credit Card Logo

   Qty: 1

Part #: C-5700

Desc 1: Mounting Bracket

Desc 2: Surface Mount

   Qty: 1

Part #: C-0141

Desc 1: Screw

Desc 2: 8-32 x 1-1/2" - Cap

   Qty: 2

1. Remove any cover or card reader plate attached to the payment device mounting bracket.

2. Place the C-5701 Mounting Plate behind the payment device mounting bracket and align the set of lower mounting points with that of the out set of threaded holes on the C-5701 Mounting Plate. Ensure the inner set of threaded holes are accessible through the central opening in the MayTag payment device bracket. Attach using (2) C-1060 8-32 x 3/8" Screws.

3. Place the C-5700 Mounting Bracket over the front of the assembly so that the set of circular openings align with the threaded holes of the C-5701 Mounting Plate accessible through the central opening. Attach using the remaining (2) C-1060 8-32 x 3/8" Screws.

Part #: C-6982

Desc 1: Maytag MLG22PD Bracket

Desc 2: F2

   Qty: 1

Part #: C-5414

Desc 1: F2/F3 Std. Mounting Bracket

Desc 2: Sheet metal base

   Qty: 1

Part #: C-5420

Desc 1: Screw

Desc 2: 10-32 x ¼" - Pan

   Qty: 2

Part #: C-5436

Desc 1: Screw

Desc 2: 10-32 x 1" - Pan MS

   Qty: 2

Part #: C-5416

Desc 1: Screw

Desc 2: 8-32" x 3/8" - Button - Torx

   Qty: 2

1. Insert C-6982 MayTag Adapter Bracket into the payment device opening and align behind the bracket so the larger hole is towards the bottom. Then use (2) C-5420 10-32 x 1/4" Pan Screws to secure to the machine.
   

   

2. Align the C-5414 F2 Standard Mounting Bracket with the holes in the C-6982 MayTag Adapter Bracket and attach together using (2) C-5436 10-32 x 1" Pan Screws.
   

   

Part #: C-5101

Desc 1: Spade Taps

Desc 2: 18-14 AWG

   Qty: 3

Part #: C-5210

Desc 1: Power Adapter Harness

Desc 2: CGI

   Qty: 1

Part #: C-5500

Desc 1: Power Extension Harness

Desc 2: 25.5"

   Qty: 1

Part #: C-5602R1

Desc 1: Power Converter

Desc 2: SMT-012-018VW

   Qty: 1

1. Tap power as described in the Fascard Reader Install - Universal Concepts document by connecting the C-5210 Power Adapter Harness to the power distribution panel inside the machine.

   1. 120vac: Connect the blue wire to L1 and the brown wire to N.

   2. 240vac: Connect the blue wire to L1 and the brown wire to L2.

   3. Connect the green wire to ground.

2. Connect the opposite end of the C-5210 Power Adapter Harness to the C-5602R1 Power Converter.

3. Connect the C-5500 Power Extension Harness to the appropriate connector on the C-5602R1 Power Converter. The remaining cable end connects to the FasCard reader.

Part #: C-5362

Desc 1: Coin Sense Harness

Desc 2: MLG

   Qty: 1

1. Disconnect the Coin Drop from the Machine Control Assembly.

2. Connect the C-5362 Coin Sense Harness to the harness connected to the Coin Drop.

Part #: C-6362

Desc 1: Coin Sense Harness

Desc 2: MLG

   Qty: 1

1. Disconnect the Coin Drop from the Machine Control Assembly.

2. Connect the C-6362 Coin Sense Harness to the harness connected to the Coin Drop.

Part #: C-5364

Desc 1: Machine Start Harness

Desc 2: Maytag MFR

   Qty: 1

1. Connect the C-5364 Machine Start Harness to the AA3 connector on the Machine Control Assembly.

1. Feed remaining harness ends through mounting bracket.

2. For serial setups:

   1. Connect the free end of the Machine Start Harness to port 1 (Serial Connection Port) as shown in the image above.

   2. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

3. For coin pulse setups:

   1. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

4. Connect the the Cat5 cables running to and from the adjacent machines to ports labeled 3 (Line Connection Ports) as shown in the image above.

5. Secure the LaundryCard reader to the bracketry using included hardware.

1. Feed remaining harness ends through mounting bracket.

2. For serial setups:

   1. Connect the free end of the Machine Start Harness to port 1 (Serial Connection Port) as shown in the image above.

   2. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

3. For coin pulse setups:

   1. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

4. Connect the free end of the Power Harness to port 1.

5. Secure the L2 reader to base as described in FasCard F2/F3 Reader Installation Guide - Front Mount.

1. Feed remaining harness ends through the mounting hole as described in the F1 Reader Mounting Guide.

2. Connect the free end of the Machine Start Harness to port 1 (Serial Connection Port) as shown in the image above.

3. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

4. Connect the free end of the Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.

5. Connect the free end of the Power Extension Harness to port 4 (Power Harness Connection Port) as shown in the image above.

6. Secure the FasCard reader to base as described in the F1 Reader Mounting Guide.

1. Feed remaining harness ends through the mounting hole as described in FasCard F2/F3 Reader Installation Guide - Front Mount.

2. For Serial Setups:

   1. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

   2. Connect the free end of the Machine Start Harness to port 5 (Serial Connection Port) as shown in the image above.

3. For Pulse Setups:

   1. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

4. Connect the free end of the Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.

   1. For dual coin drop setups connect the secondary Coin Sense Harness to port 4 (Coin Sense Harness Connection Port) as shown in the image above.

5. Connect the free end of the Power Harness to port 1.

6. Secure the FasCard reader to base as described in FasCard F2/F3 Reader Installation Guide - Front Mount.

TODO