3602 Reader Install Guide

Warning!

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses.

It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Overview

Equipment Details

Type: Washer Extractor
Manufacturer: Alliance
Make: [VARIES]
Model Length: 18

Associated Models

HCT020VCAVXB60BA00
HCT020VL0VXB60B000
HCT020VP0VXB60BA00
HCT020VX0VXB60BA00
HCT020VY0FXB60BA00
HCT020VY0VXB60BA00
HCT030VCAVXB60BA00
HCT030VY0VXB60BA00
HCT040VCAFXB60BA00
HCT040VCAVXB60BA00
HCT040VL0VXB60B000
HCT040VP0VXB60BA00
HCT040VY0FXB60BA00
HCT040VY0VXB60BA00
HCT060VCAFXB60BA00
HCT060VCAVXB60BA00
HCT060VL0VXB60B000
HCT060VP0VXB60BA00
HCT060VY0FXB60BA00
HCT060VY0VXB60BA00
HCT080VCAFXB60BA00
HCT080VCAVXB60BA00
HCT080VL0VXB60B000
HCT080VP0VXB60BA00
HCT080VY0FXB600000
HCT080VY0FXB60BA00
HCT080VY0VXB60BA00
HCT100VCAVXB60BA00
HCT100VX0VXB60BA00
HCT100VY0VXB60BA00
SCT020VCAFBB60BA00
SCT020VCAFXB60B000
SCT020VCAVBB60BA00
SCT020VCAVXB500000
SCT020VCAVXB600000
SCT020VCAVXB60BA00
SCT020VDAVXB500000
SCT020VY0FXB60B000
SCT020VY0FXB60BA00
SCT020VY0VBB60BA00
SCT020VY0VXB500000
SCT020VY0VXB60BA00
SCT030VCAFBB60BA00
SCT030VCAFXB60B000
SCT030VCAFXB60BA00
SCT030VCAVXB500000
SCT030VCAVXB600000
SCT030VCAVXB60BA00
SCT030VY0FXB60B000
SCT030VY0FXB60BA00
SCT030VY0VXB500000
SCT030VY0VXB60BA00
SCT040VCAFXB60B000
SCT040VCAFXB60BA00
SCT040VCAVBB60B000
SCT040VCAVXB500000
SCT040VCAVXB600000
SCT040VCAVXB60B000
SCT040VCAVXB60BA00
SCT040VDAVBB500000
SCT040VEAVXB50FA00
SCT040VP0FXB60BA00
SCT040VX0VXB60B000
SCT040VY0FXB60B000
SCT040VY0FXB60BA00
SCT040VY0VBB60MA00
SCT040VY0VXB500000
SCT040VY0VXB50E00P
SCT040VY0VXB60BA00
SCT060VCAFBB60BA00
SCT060VCAFXB60B000
SCT060VCAFXB60BA00
SCT060VCAVXB500000
SCT060VCAVXB600000
SCT060VCAVXB60BA00
SCT060VEAVXB50FA00
SCT060VTAFXB60BA00
SCT060VY0FXB60B000
SCT060VY0FXB60BA00
SCT060VY0VXB500000
SCT060VY0VXB60BA00
SCT080VCAFBB60BA00
SCT080VCAFXB600000
SCT080VCAFXB60B000
SCT080VCAFXB60BA00
SCT080VCAVBB60BA00
SCT080VCAVXB60B000
SCT080VCAVXB60BA00
SCT080VEAVXB50FA00
SCT080VP0FXB60BA00
SCT080VY0FXB60BA00
SCT080VY0VXB500000
SCT080VY0VXB60B000
SCT080VY0VXB60BA00
SCT100VCAVX1600000
SCT100VCAVXB60B000
SCT100VCAVXB60BA00
SCT100VCAVYB60BA00
SCT100VY0VXB500000
SCT100VY0VXB60B000
SCT100VY0VXB60BA00

Recommended Tools and Supplies

Drill
1 1/8" Tungsten Carbide Tipped Hole Cutter
Cutting Oil
9/64" Drill Bit
Center Punch
Hammer
Fine Point Permanent Marker
Pliers
Tape Measure

Installation

Install Mounting Hardware

I-M0003

Part #: C-6801

Desc 1: F2/F3 Reader Mounting Kit

Desc 2: Universal

Qty: 1

Place the C-6700-TEMP Drill Template on the desired mounting location.
Verify included harnesses will reach desired location without encountering interference from internal machine components.
Refer to Touchscreen Reader Mounting Guide (F2 & F3) for further instructions.

I-M0176

Part #: C-6965

Desc 1: F2 Quantum Touch Bracket

Desc 2:

Qty: 1

Part #: C-6801

Desc 1: F2/F3 Reader Mounting Kit

Desc 2: Universal

Qty: 1

Part #: C-5365

Desc 1: Bypass Harness

Desc 2: Alliance Coin Vault Bypass

Qty: 1

Disconnect wires connected to vault service switch and bridge connection using C-5365 Bypass Harness.
Remove the four (4) T25 screws indicated below:
Pull panel away from machine exposing the factory plate / Coin Drop
Loosen the two (2) left retaining screws (Green) and remove the remaining screws on the bracket (Blue) and slide the bracket off the machine.
Slide the C-6965 QT Mounting Bracket onto the loose screws and tighten. Add remaining screws to the corresponding holes on the bracket and tighten.
Re-secure the front panel to the machine.
Attach the C-5414 Reader Bracket to the C-6965 QT Mounting Bracket using C-5702 Chase Nipple and C-5703 Nut.
Feed all reader harnesses through the center hole.

Connect Power

I-P0002

Part #: C-6204-40

Desc 1: Power Adapter Harness

Desc 2: F2, 12vDC Pow Harness - 40"

Qty: 1

Connect the C-6204-40 Power Adapter Harness to the H10 connection on the machine control board.
Secure the green wire beneath the ground screw.
Connect the opposite end of the C-6204-40 Power Adapter Harness (3-pin molex) into the back of the F1 Reader.

Connect Coin Sense Harness

I-S0027

Part #: C-6250

Desc 1: Coin Sense Harness

Desc 2: F2

Qty: 1

Disconnect the Coin Drop from the Machine Control Assembly.
Connect the C-6250 Coin Sense Harness to the harness connected to the Coin Drop.

Connect Machine Interface Harness

I-T0003

Part #: C-5240

Desc 1: Machine Start Harness

Desc 2: Alliance ACA

Qty: 1

Connect the C-5240 Machine Start Harness to the H3 connector on the Machine Control Assembly.

Connect and Mount Reader

Item No.	Component	Notes
1	Power Connection Port	Utilizes the same power harnesses as the first generation FasCard reader.
2	Pulse Connection Port	Connection point for pulse machine start harnesses.
3	Coin 1 Connection Port	This is the connection point for the harness input associated with Coin 1.
4	Coin 2 Connection Port	This is the connection point for the harness input associated with Coin 2.
5	Serial Connection Port	This is the connection point for serial machine start harnesses.

Feed remaining harness ends through the mounting hole as described in the Touchscreen Reader Mounting Guide (F2 & F3).
Connect the free end of the C-5240 Machine Start Harness to port 5 (Serial Connection Port) as shown in the image above.
Connect the free end of the C-6250 Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.
Connect the free end of the C-6204-40 Power Harness to port 1.
Secure the FasCard reader to base as described in the Touchscreen Reader Mounting Guide (F2 & F3).

Machine Configuration

TODO

CCI Software Configuration

Machine Control	Pulse	Serial
Quantum Touch (Midas)	SingleVend (MLV+) / 80ms	Alliance Quantum Touch Washer Extractor

3602 Reader Install Guide

Overview

Equipment Details

Associated Models

Recommended Tools and Supplies

Installation

Install Mounting Hardware

Connect Power

Connect Coin Sense Harness

Connect Machine Interface Harness

Connect and Mount Reader

Machine Configuration

CCI Software Configuration

Additional Resources